Tripp-Lite isobar HT1210ISOCTR Manuel Du Propriétaire

1111 W. 35th Street Chicago, IL 60609 USA
Customer Support: (773) 869-1234
Safety
IMPORTANT SAFETY INSTRUCTIONS.
SAVE THESE INSTRUCTIONS.
This manual contains instructions and warnings that should be followed during the
installation and operation of all Tripp Lite Console Component Power Centers.
Failure to heed these warnings will void your warranty.
• The Console Component Power Center features an internal protection that will
disconnect the surge-protective component at the end of its useful life but will
maintain power to the load—now unprotected.
• Do not connect the Console Component Power Center to an ungrounded outlet. Do
not use with 2-wire extension cords or adapters. Do not plug extension cords into
the Console Component Power Center.
Features
MODEL: HT1210ISOCTR
Front Panel
A
Illuminated "ON/OFF" Power Switch: turns power on and off at all of the
outlets.
B "ON" LED: indicates that AC power is available at the Console Component
Power Center's outlets. This LED will illuminate when the Power Switch is set to
"ON".
"POWER" LED: indicates AC power is available at the wall outlet.
C
"GROUND" LED: indicates wall outlet is grounded and surge protection can
D
properly function.
"PROTECTED" LED: indicates the surge suppression components are intact
E
and providing complete protection against surges. If this LED does not illuminate,
some of the surge suppression components are not functioning, and the unit should
be replaced. Call Tripp Lite Customer Support at (773) 869-1234.
"SELECT" Switch: selects controllable IR outlets (labeled "IR1", "IR2", "IR3"
F
and "IR4" on the rear panel of the Console Component Power Center) to be turned
on or off using the "ENTER" Switch. See "IR Outlet Control" in the "Optional
Installation" section for setting procedure.
"ENTER" Switch: turns controllable IR outlets on or off (after they have first
G
been selected using the "SELECT" Switch). See "IR Outlet Control" in the
"Optional Installation" section for setting procedure.
"DELAY/ADJUST" DIP Switches: select the delay interval (0, 1, 10 or 30
H
seconds) when turning on or off multiple IR outlets in a sequence using a remote.
See "IR Outlet Control" in the "Optional Installation" section for setting
procedure.
"OUTLET SELECT" LEDs: indicate which controllable IR outlets (labeled
I
"IR1", "IR2", "IR3" and "IR4" on the rear panel of the Console Component
Power Center) have been selected using the "SELECT" Switch. Each LED will
flash when its corresponding IR outlet has been selected. Each LED will
illuminate continuously when power has been turned on at the outlet.
All manuals and user guides at all-guides.com
www.tripplite.com
Español: p.5
A
B C D E F G
isobar ®
Console Component
Power Center with
Digital IR Remote
Model: HT1210ISOCTR
Français: p.9
• The Console Component Power Center is designed for indoor use only. Install the
Console Component Power Center away from heat-emitting appliances such as
radiators or heat registers. Do not install where excessive moisture is present.
• Never install electrical, telephone, network or coaxial wiring during a lightning
storm.
• Do not drill into any part of the housing or open the housing for any reason. There
are no user-serviceable parts inside.
J
H I
K
Front Panel
J "POWER ON" LEDs: indicate which controllable IR outlets have been turned
ON using the "ENTER" Switch. Each LED will flash when its corresponding IR
outlet has been selected. Each LED will illuminate continuously when power has
been turned on at the outlet.
K Infrared (IR) Sensor: is for use with either the included IR remote or a universal
learning IR remote (user-supplied)* to control IR outlets. Program the outlets to
turn on or off individually or in a sequence. If the sensor is covered, a remote IR
sensor (user-supplied) can be connected to the IR sensor input on the rear panel of
the Console Component Power Center.
* The user-supplied remote must be a universal learning type to work with the included remote.
L "Input Voltage" Digital LED Display: clearly shows voltage variations of
incoming utility power. The Console Component Power Center can alert you to
abnormal voltage, but cannot regulate it. If persistent low or high voltage
conditions continually affect equipment performance, consider purchasing a
Tripp Lite UPS system or line conditioner.
M "Current Usage" LED Display: allows you to get the maximum use from your
Console Component Power Center by showing you the total amperage load of all
of your connected components. CAUTION: the total amperage capacity of the
Console Component Power Center is 15 amps. Any amperage loads that exceed
15 amps will cause the circuit breaker to trip. Action should be taken to reduce
connected load and reset the circuit breaker.
N
Rackmount Hardware: allows 2U mounting in standard sized racks.
O
Removeable Console Feet: allow placement on a shelf as a console component
within a system. Unscrew feet prior to rackmounting the Console Component
Power Center.
1
Owner's Manual
L M O N