Fellowes Starlet 2 plus 120 Instructions D'utilisation page 2

LOCATION OF CONTROLS
1
2
3
7
3
Starlet2+_407888_RevC_25L_103116.indd 3-5
All manuals and user guides at all-guides.com
ENGLISH
LOCATION OF CONTROLS
1. Punch handle
2. Edge guide selector
4 3. Edge guide
4. Paper entry
CAPABILITIES
5
Punching Capacity
Paper sheets
- 70-80g / 20lb 12 sheets
Transparent covers
- 100-200 micron / 4-8 mil 2 sheets
- 200+ micron / 8+ mil 1 sheet
Other standard covers
- 160-270g / 40-60 lb 2 sheets
- 270+g / 60+ lb 1 sheet
Binding Capacity
Max comb size 16mm comb
6
Max document (80g / 20lb) 120 sheets
IMPORTANT SAFETY INSTRUCTIONS
CAUTION -
Please read before use and keep for future reference.
When punching;
- always ensure the machine is on a stable surface
- test punch scrap sheets and set the machine before punching final documents
- remove staples and other metal articles prior to punching
- never exceed the machines quoted performance
- punch front and back covers first
- punch sheets in small batches that do not overload the machine or the user
- lift punch handle to open waste tray, when punch handle is down the waste tray is locked
COMB DIAMETER & DOCUMENT SIZES
6mm 8mm
1/4" 5/16"
2-20 sheets 21-40 sheets
4
5. Waste tray
6. Document measure
7. Comb lever
Technical Data
Paper dimensions A4
Punching slots 21 (A4)
Slot pitch 14.28mm / 9/16"
Adjustable edge guide A4 or A5
Waste tray capacity 1000 sheets
Net weight 3.3kg / 7.3lb
Dimensions (HxWxD) 135(390) x 480 x 195mm
5.5"(15.5") x 19" x 8"
12
SHEETS
LIGHT USE
PUNCH CAPACITY
120 16
SHEETS MM
BIND CAPACITY MAX COMB SIZE
Problem
Punched holes are not central
Machine will not punch
Punch holes are not parallel to edge
10mm 12mm 16mm
3/8" 1/2" 5/8"
Partial holes
Damaged hole edges
41-55 sheets 56-90 sheets 91-120 sheets
Waste tray leaks
Cannot access document measure feature
SET UP
A4 A5
1. Ensure the machine is on a stable 2. Lift the punch handle. Check the 3. Ensure the comb-opening mechanism
surface. Lift the punch handle to its waste tray is empty and correctly fitted. is closed.
upright position.
BEFORE YOU BIND
A4 A5
1. Select either A4 or A5 paper size and 2. Place the binding comb into the 3. Open the binding comb by turning the
test punch scrap sheets. Select the cor- opening mechanism and fully engage comb lever. Take care not to open the
rect comb diameter to suit the document the opening plate by sliding the comb comb too far.
(see chart). to the left.
STEPS TO BIND
1. Insert sheets fully into the punch slot. 2. When all punched sheets are loaded 3. To remove the document, slide the
Align the sheets to the edge guide. onto the comb, close the comb lever. comb to the right and lift up the docu-
ment.
TROUBLESHOOTING
Possible cause Solution
Edge guide not set Adjust edge guide until hole pattern is correct
Blockage Check waste tray is empty. Check for blockage to paper entry
Take stiff cardboard and slide into the paper entry. Move the cardboard
Debris is stuck below dies
sideways to release any stray clippings into the waste tray
Sheets not correctly aligned to punch pattern Adjust edge guide and test punch scrap sheets until correct
Punch plastic covers with paper sheets. Reduce number of sheets being
Possibly overloading the machine
punched
Waste tray is not correctly inserted or 'burst feature'
Check waste tray is empty and 'burst feature' is closed
has activated
Check punch handle is fully raised then remove the waste tray & docu-
Document measure is part of the waste tray
ment measure
5
10/31/16 4:27 PM