Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: Utility Knife, Phillips screwdriver
Fastener Kit: 24830F
Wrenches: ¾"
Drill Bits: N/A
1
Qty. (4)
Carriage Bolt ½-13 x 4.50 Gr2
2
Qty. (2)
Top Plate, 2.00 x 4.50 w/Square holes
3
Qty. (4)
Flanged Lock Nut, ½-13
4
Qty. (2)
Carriage Bolt ½-13 x 1.75 Gr5
1.
Remove the three (3) screws holding the plastic bumper fascia to the bottom of the trunk pan.
2.
Remove the spare tire and jack from inside trunk.
3.
Remove the two (2) rearmost plastic drain plugs from the bottom of trunk pan.
4.
Cut a notch in the lower part of the plastic fascia, approximately 3-1/4" wide x 3" deep, centered on vehicle, as shown in figure 2.
Obtain vehicle owner's permission before cutting plastic fascia.
5.
Gently pull fascia down and rearward, and install the Top Plates and 4.50 long carriage bolts on top of the bumper support tubes.
6.
Raise hitch into position, aligning the slots in hitch brackets with long carriage bolts and loosely install the flanged locknuts onto carriage
bolts.
7.
Install the 1.75 long carriage bolts, spacer blocks, conical toothed washers, and hex nuts from inside of trunk pan and through holes in
forward hitch brackets.
8.
Tighten all 4.50 long Gr2 carriage bolts with torque wrench to 50 Lb.-Ft. (68 N*M)
9.
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
10.
Re-install the two outer screws through bumper fascia and into the trunk pan.
11.
Re-install the jack and spare tire into trunk.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008 Cequent Towing Products
Installation Instructions
Fascia trimming required. Obtain vehicle
owner approval before cutting.
Plastic Fascia
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
End Panel
Trunk Pan
Figure 1
Audi A4 Sedan
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg.) Max Gross Trailer Weight
200 LB (90.8) Max Tongue Weight
Wiring Access Location: PC1, PC2
4
5
6
7
5
Qty. (2)
6
Qty. (2)
7
Qty. (2)
Sheet 1 of 3
Manufacturer's Rating or
1
2
3
3-1/4"
3"
Figure 2
Fascia Trim Detail
Bottom View
Spacer Block, ¼ x 2 x 2
Conical toothed washer, 1/2
Hex nut, 1/2-13
24830N
10-29-08
Part Numbers:
24830
77203
60219
Centerline
Of Vehicle
Fascia to
Be Trimmed
Rev. A
Form F206 Rev A 5605
Publicité
Manuels Connexes pour Cequent Towing Products 24830
Sommaire des Matières pour Cequent Towing Products 24830
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24830N 10-29-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 1 de 3 24830N 10-29-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Sheet 1 of 3 24830N 10-29-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...