Publicité
MPK 130
TWO WAY SYSTEM
200 W
TECHNICAL SPECIFICATION
Component
Size
Woofer
mm (in.)
Tweeter diaphragm mm (in.)
Voice Coil Ø
Woofer
mm (in.)
Tweeter
mm (in.)
W peak
Power Handling
W continuos
Sensitivity
dB SPL
Impedance
Ω
Frequency
Hz
Response
Midrange
Crossover
Tweeter
Adjustment
Tweeter Level
Weight of one component
Woofer
kg (lb)
Tweeter
kg (lb)
Crossover
kg (lb)
ELECTRO-ACOUSTIC
PARAMETERS
D
mm
Xmax
mm
Re
Ω
Fs
Hz
Le
mH
Vas
I
Mms
g
Cms
mm/N
BL
•
T
m
Qts
Qes
Qms
Spl
dB
.3
2-way system
130 (5)
29 (1.14)
25 (1)
25 (1)
200
100
91
4
÷
60
22,5k
Low pass 3,5 kHz @ -6 dB Oct.
Hi pass 3,5k Hz @ -12 dB Oct.
0 / +2 dB
0.95 (2.09)
0.07 (0.15)
0.16 (0.35)
MP 25.3
MP 130.3
29
110
-
±2,75
3,9
3,1
1200
90
0,02
0,25
-
3
0,17
10,5
0,1
0,24
1,6
5,3
0,55
0,64
1,98
0,74
0,57
5,1
91
92
Elettromedia
- 62018 Potenza Picena (MC) Italy - T +39 0733 870 870 - F +39 0733 870 880 - www.elettromedia.it
MP 25.3:
1.
Tetolon fiber soft dome, for a natural yet detailed reproduction of musical
nuances.
2.
"Center Tuning Duct" geometry, for lower resonance frequency and reduced
harmonic distortion.
3.
High density flux Neodymium magnet, optimized for utmost control during
high energy dynamic transients in the mid-high frequency range.
4.
25mm ferrofluid-cooled mobile voice coil.
5.
Rear chamber filled with selected damping material and sized for lower Fs,
to ensure a well damped high pass frequency roll-off, allowing low cut-off
frequency crossover point.
6.
Faceplate featuring FEM (Finite Element Modeling) optimized geometry, for
high linearity in off-axis installations.
7.
Wide array of installation accessories, for an easy OEM integration.
MP 130.3:
1.
Pure copper voice coil wound on a Polyamide former combining excellent
power handling combined with fast musical transients response.
2.
Exponential V-cone® profile pressed-pulp cone with cotton fibers, combining
stiffness and lightweight for a wide frequency response. Cone profile
geometrically optimized for utmost linearity and dispersion in the mid
frequency range.
3.
"Boundary Free" rubber surround, for improved efficiency and wider mid-bass
frequency.
4.
High density flux ferrite magnet combined with very low carbon content iron
plates, for low distortion at high power levels.
5.
Low mounting depth, acoustically transparent aluminium alloy basket with
spider vent holes.
6.
Full protection metal mesh grill featuring the aluminium Hertz logo and
attractive look mineral powder coated inner grill are included for several install
combinations.
MPCX 2.3:
1.
Two-position (0 / +2 dB) switch for tweeter level adjustments, to fine-tune
the transducers emission.
2.
160V extremely high quality bi-metallized polyester film capacitors with
ultra-low DF, for maximum sound transparency and neat mid/hi-frequencies.
3.
1mm pure copper wire low series resistance inductors, for low dissipation
losses on the woofer section where high transient currents are demanded.
4.
Small footprint design for easy installation, with top vent grille for efficient
heat dissipation.
12
Publicité
