Westin Automotive Products 32-1690 Consignes

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-1690 32-1695
32-1800 32-1805
ITEM QTY
1 1 BULL BAR ASSEMBLY
2,3 2 BRACKET, PASSENGER (2) AND DRIVER (3)
4 2 PLASTIC PLUG
5 4 RUBBER BUMPER
6 4 M12- 1.75 X 30MM SERRATED FLANGE BOLT
7 4 M12 FLAT WASHER
8 4 M12 LOCK WASHER
9 4 M12 SERRATED FLANGE HEX NUT
10 4 M12-1.25 X 30MM HEX HEAD BOLT
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 SOPORTE, ACOMPAÑANTE
4 2 TAPONES DE PLÁSTICO
5 4 PARACHOQUES DE HULE
6 4 DENTADA BRIDA EMPERNADA DE M12-1.75 X 30MM
7 8 ARANDELAS PLANAS DE M12
8 4 ARANDELAS DE PRESIÓN DE M12
9 4 DENTADA BRIDA TUERCA HEXAGONAL DE M12
10 4 PERNOS CON CABEZA HEXAGONAL DE M12-1,25 X 30MM
1 1 LA BULL BAR
2,3 2 SUPPORTS, PASSAGER (2) ET CONDUCTEUR (3)
4 2 BOUCHON DE PLASTIQUE
5 4 PARE-CHOCS EN CAOUTCHOUC
6 4 DENTELE BRIDE BOULON M12-1.75 X 30MM
7 8 RONDELLES PLATES M12
8 4 RONDELLES PLATES M12
9 4 NUT HEX DENTELE BRIDE M12
10 4 BOULONS A TETE HEXAGONALE M12-1,25 X 30MM
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before
STEP 1.
beginning.
NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not required, but strongly
STEP 2.
recommended. If local/state laws requires a license plate, license plate relocation kit 32-0055 is available.
STEP 3. Remove lower air dam by removing six bolts from bottom of bumper. Save for later installation.
STEP 4. Determine passenger and driver brackets and install as shown. NOTE: If vehicle is equipped with optional tow hooks, they
must be removed.
STEP 5. Temporarily attach Bull Bar to mount brackets as shown. Center and level. When centered, torque mount bracket to vehicle
bolts to 55 Ft.Lbs.
STEP 6. Re-attach lower air dam and trim as necessary to fit around mount bracket and Bull Bar. It may be necessary to remove Bull Bar
from brackets to fully attach lower air dam.
STEP 7. Re-attach Bull Bar to mount brackets using M12 serrated flange fasteners. Level and adjust Bull Bar as desired and tighten all
fasteners. SEE FIGURE 2. Recommended torque values are 55 Ft. Lbs. for M12 fasteners.
LIGHT INSTALLATION: Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension and socket for
correct size of nut supplied, insert through large clearance hole in bottom of cross tube. Thread nut and washers on stud and
tighten. SEE FIGURE 1. NOTE: A short socket, not a deep well works best to get the nut started.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION:
APLICACIÓN:
APPLICATION:
1
CONTENTS - CONTENIDO
(2) Y EL CONDUCTOR
2005-12 NISSAN FRONTIER/XTERRA
2005-07 NISSAN PATHFINDER
2008-12 NISSAN PATHFINDER
NISSAN FRONTIER/XTERRA
NISSAN PATHFINDER , MOD. 2005-07
NISSAN PATHFINDER,, MOD. 2008-12
NISSAN FRONTIER/XTERRA
NISSAN PATHFINDER 2005-07
NISSAN PATHFINDER 2008-12
- CONTENU
(3)
W11-0025 75-0507 REVISION I 8/24/11
, MOD. 2005-12
2005-12
2
TOOLS - HERRAMIENTA
18MM SOCKET
10MM SOCKET
RATCHET
TORQUE WRENCH
UTILITY KNIFE
DADO DE 18MM
DADO DE 10MM
MANERAL
LLAVE DE TORQUE
NAVAJA
DOUILLE DE 18MM
DOUILLE DE 10MM
CLIQUET
CL DE COUPLE É
COUTEAU
3
- OUTILS