BIXOLON SRP-350 Guide D'installation

Masquer les pouces

page de 8

/ 8
Signets

Les langues disponibles

Liens rapides

Télécharger ce manuel

KN04-00009A (Rev.1.5)

◈ Information

This Installation Guide includes a brief outline of information necessary for product

installation. For more detailed installation information, please refer to the user manual in the

enclosed CD. The contents of the CD include the following.

1. Manual: User Manual, Code Chart, Control Commands

2. Drivers: Windows Drivers, OPOS Drivers

3. Utilities: a logo download tool

◈ Components

Cable Cover

SRP-350

AC/DC Adaptor

◈ Connecting the Cables

1. Turn off the printer and the host ECR (host computer).

2. Plug the power cord into the Adaptor, and then plug the Adaptor into the power connector

of the printer.

3. Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface

connector cable accordingly.

4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer.

Interface connector

Interface cable

(Serial/Parallel/USB/Ethernet)

◈ Installing the Paper Roll

※ Note: Adjusting the Paper Near-End Sensor

Near end sensor tab

Paper Roll

Power Cord

Installation Guide

Drawer kick-out connector

Power connector

Adaptor

Drawer

kick-out

cable

Power cord

1. Open the paper roll cover by pressing the cover-

open button.

2. Insert a new paper roll, making sure to align it

properly.

3. Pull out a small amount of paper, and close the

cover.

※ Note

When closing the cover, press down on the center

of the cover to ensure that the paper is in contact

with the roller.

The SRP-350 has a paper near-end sensor that

provides notice that the paper roll is nearly

exhausted. When the paper is running low, the lamp

on the apparatus is lit red. If the lamp is activated

even when sufficient paper remains, adjust the

near-end sensor setting by pushing the tab upward

towards1.

Printer Installation Guide

THERMAL PRINTER SRP-350

◈ Using the Operation Panel

Procuct Installation CD

◈ Setting the Dip Switches

Changing Dip Switch settings must be done when the printer is off. Any changes done while

the printer is on will not be processed.

1. Serial Interface

• DIP Switch 1

1-1

Auto Line Feed

1-2

Reserved

1-3

Handshaking

1-4

Word length

1-5

Parity Check

1-6

Parity Selection

1-7

Baud rate Selection

1-8

• DIP Switch 2

2-1

Code Page Selection

2-2

Internal bell control

2-3

Auto Cutter Selection

2-4

Code Page Selection

2-5

Select Print Density

2-6

2-7

Near End Sensor Status

2-8

Code Page Selection

2. Parallel / USB Interface

• DIP Switch 1

1-1

Auto Line Feed

1-2

1-3

1-4

1-5

1-6

1-7

1-8

• DIP Switch 2

2-1

Code Page Selection

2-2

Internal bell control

2-3

Auto Cutter Selection

2-4

Code Page Selection

2-5

Select Print Density

2-6

2-7

Near End Sensor Status

2-8

Code Page Selection

• Table 1 – Baud Rate Selection

Transmission Speed

9600

19200

38400

57600

• Table 2 – Select Print Density

Print Density

1 (Light)

4 (Dark)

• Table 3 – Code Page Selection

Code Page

PC 437

PC 737

PC 852

PC 857

PC 864

PC 866

WPC 1251

WPC 1254

• POWER (LED)

When turning on the power, a green LED will be lit.

• ERROR (LED)

When an error occurs, a red LED will be lit.

(e.g. no paper, cover ajar, etc.)

• PAPER (LED)

Red LED will be lit when the paper roll is running low. The LED blinks

when the printer is in self-test standby mode or macro execution standby

mode.

• FEED (Button)

Press the FEED button once to discharge extra paper. Holding down the

FEED button will discharge paper continuously until the button is

released.

Function

Enable

XON/XOFF

7 bits

Yes

EVEN

Refer to the following Table 1

Function