BIXOLON SRP-270 Guide D'installation

KN02-00002A (Rev.1.8)
◈ Information
This Installation Guide includes a brief outline of information necessary for product
installation. For more detailed installation information, please refer to the user manual in the
enclosed CD. The contents of the CD include the following.
1. Manual: User Manual, Code Chart, Control Commands
2. Drivers: Windows Drivers, OPOS Drivers
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
SRP-270A
Ribbon Cartridge Paper Roll
AC/DC Adaptor Power cord
◈ Connecting the cables
1. Turn off the printer and the host ECR (host computer).
2. Plug the power cord into the Adaptor, and then, plug the Adaptor into the power connector of the
printer.
3. Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface connector
cable accordingly.
4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer.
※ Do not use an adapter that was not supplied with the printer.
Adaptor
Power cord
Drawer kick-out
Interface cable
(Serial/Parallel/USB/Ethernet)
◈ Installing the Ribbon Cartridge
1. Before inserting the ribbon cartridge, turn the knob clockwise to prevent twisting of the ribbon.
2. Open the front cover of the printer and remove the old ribbon cartridge, if any.
◈ Installing the Paper Roll
1. Open the printer cover and insert the new paper
roll in the correct direction.
Insert the end of the paper roll into the entrance.
(The SRP-270 C and D types automatically enter
and cut the paper.)
* SRP-270 A and C types: Uses single-ply paper
rolls
* SRP-270 D type: Uses double-ply paper rolls
3. Push and lock the automatic cutter cover, and close the printer cover.
4. When the 'ERROR' indicator lamp is lit and the 'PAPER' lamp blinks, press the 'FEED' button to
complete preparations for printing.
SRP-270C SRP-270D
Procuct Installation CD Procuct Installation CD Procuct Installation CD
Exclusive for
SRP-270D
CD
Installation Guide
Power connector
Drawer kick-out
cable
connector
Interface
connector
3. Insert the ribbon cartridge as shown in the
figure so that the ribbon is aligned to the
rear of the printer head.
4. To allow the ribbon to move freely within
the cartridge when inserting the ribbon
cartridge, turn the knob clockwise once
more.
5. Close the front cover of the printer.
※ Note
Using unauthorized ribbon cartridges may
result in poor printing quality or malfunction
and will void the warranty.
Refer to the User Manual to learn more about
the ribbon cartridge.
2. Installing the Double-Ply Paper Roll in the
SRP-270 D type:
After inserting the end of the paper in the
groove on the roller wheel, wrap the paper
around the groove 2~3 times. Place the roller
wheel in the slot within the case.
Printer Installation Guide
◈ Using the Operation Panel
PAPER
FEED
ERROR
◈ Setting the DIP switches
Changing Dip Switch settings must be done when the printer is off. Any changes done while
the printer is on will not be processed.
1. Serial Interface
• DIP Switch 1
SW
1-1
Emulation
1-2
1-3 Auto Cutter
Spool
1-4 Font Space
1-5
1-6 Function for Service Engineer
1-7
1-8 Type of Korean
• DIP Switch 2
SW
2-1 Auto Line Feed
2-2 Hexadecimal Dumping
2-3 Handshaking
2-4 Data Length
2-5 Parity Check
2-6 Parity Selection
2-7
Baud Rate Selection
2-8
2. Parallel / USB Interface
• DIP Switch 1
SW
1-1
Emulation
1-2
1-3 Auto Cutter
1-4 Font Space
1-5
1-6 Function for Service Engineer
1-7
1-8 Type of Korean
• DIP Switch 2
SW
2-1 Auto Line Feed
2-2 Hexadecimal Dumping
2-3 Reserved
2-4 Reserved
2-5 Reserved
2-6 Reserved
2-7 Reserved
2-8 Reserved
• Table 1 – Emulation Selection
1-1
OFF
OFF
ON
• Table 2 – Baud rate (bps) Selection
Transmission Speed
19200
2400
4800
9600
IMPACT PRINTER SRP-270
• FEED (Button)
Press the FEED button once to discharge extra paper.
• PAPER (RED)
POWER
When the printer is out of paper, a red LED will be lit.
• ERROR (RED)
When an error
occurs, a red LED will be lit.
• POWER (GREEN)
When turning on the power, a green LED will be lit.
Function ON
Refer to the following table 1
Enable
2
Combination
Function ON
Always
enable
Yes
XON/XOFF
7 bits
Enable
EVEN
Refer to the following table 2
Function ON
Refer to the following table 1
Enable
2
Combination
Function ON
Always
Enable
Yes
-
-
-
-
-
-
1-2
OFF
ON
OFF
2-7
ON
OFF
ON
OFF
OFF Default
OFF
ON
Disable ON
3 OFF
-
-
OFF
Completion OFF
OFF Default
Always
OFF
disable
No OFF
DTR/DSR OFF
8 bits OFF
Disable OFF
ODD OFF
OFF
OFF
OFF Default
OFF
ON
ON ON
3 OFF
-
-
OFF
Completion OFF
OFF Default
Always
OFF
Disable
No OFF
- OFF
- OFF
- OFF
- OFF
- OFF
- OFF
Mode
EPSON
Citizen
Star
2-8
ON
ON
OFF
OFF