Kärcher MT CS 250/36 Mode D'emploi page 16

 Check the chain for sufficient sharpness, if neces-
sary, invert the guide rail or replace the chain (see
Chapter Replacing the chain).
 Check the device for damage.
 Check all pins, nuts and screws for tightness.
Adjusting the chain tension
1. With the Multi-Tool assembled, remove the battery
pack (see Multi-Tool MT 36 Bp operating instruc-
tions).
2. Release the guide rail nut.
Illustration I
3. Adjust the chain tension with the screw.
Illustration J
4. Check the chain tension.
Illustration F
The distance between the guide rail and the chain
must be 4,0 mm.
5. Tighten the guide rail nut.
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device stops during
operation
Problems when mount-
ing the shaft compo-
nents
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Technical data
Device performance data
Working voltage of the bat-
tery
Maximum speed
Chain oil tank volume
Cut material diameter
(max.)
Working range (max.)
Dimensions and weights
Length x width x height
Weight (with battery pack) kg
Weight
16
Troubleshooting guide
Cause
Chain blocked by clippings.
Motor has overheated
The connection points are dirty.
MT 36 MT CS
Bp 250/36
Bp
V 36
/min 10000 ±
10%
ml 200
mm 180
m 2,7
mm 951 x 946 x
197 x 117 x
188 168
2,6
kg 2,0
Replacing the chain
1. Remove the guide rail nut.
Illustration K
2. Loosen the screw to adjust the chain tension
3. Remove the bar cover.
Illustration L
4. Remove the guide rail.
5. Dispose of the old chain professionally.
6. Fit the new chain on the guide rail.
Illustration M
7. Mount the guide rail. Pay attention to the running di-
rection of the chain.
Illustration N
8. Mount the bar cover, loosely fastening the guide rail
nut.
Illustration O
9. Adjust the chain tension (see Chapter Adjusting the
chain tension).
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Remove the clippings.
 Stop working and allow the motor to cool
down.
 Clean the shaft ends of adhering dirt.
 Only place the accessories on clean sur-
faces.
Device performance data (measured with MT 36 Bp
Multi-Tool)
Sound power level as per EN ISO 11680-1 (meas-
ured with MT 36 Bp Multi-Tool)
Sound pressure level L
Uncertainty K
pA
Sound power level L
Uncertainty K
WA
Vibration value as per EN ISO 11680-1 (measured
with MT 36 Bp Multi-Tool)
Front handle hand-arm vi-
bration value
Rear handle hand-arm vi-
bration value
Uncertainty K
Subject to technical modifications.
Vibration and noise value
The total vibration values given and the noise emission
values given were measured according to a standard
test procedure and can be used to compare one tool
with another. The declared total vibration values and the
declared noise emission values can also be used for a
preliminary exposure assessment.
English
MT 36
Bp
dB(A)
pA
dB(A)
dB(A)
wA
dB(A)
2
m/s
2
m/s
2
m/s
MT CS
250/36
Bp
92,6
3,0
100,7
3,0
3,0
2,9
1,5