Specified Conditions Of Use; Advice For Operation - AEG MFE 1500 Mode D'emploi

TRANSPORT, HANDLING AND STORAGE
Diamond cutting discs must be handled and transported
with care. Use the original packaging if possible, or use
other suitable packaging.
Store the discs in a dry location where they are not
exposed to mechanical damage.
Protect cutting discs against shock, impact and harmful
environmental factors.
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.

SPECIFIED CONDITIONS OF USE

The wall-chaser machine cuts slots for cables and pipes
(masonry grooves) in any kind of brickwork with two
diamond cutting discs running parallel to each other.
Do not use this product in any other way as stated for
normal use.
Appliances used at many diff erent locations including wet
room and open air must be connected via a residual
current device (FI, RCD, PRCD) of 30mA or less.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-22:2011 + A11:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Winnenden, 2020-12-15
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under "Technical Data" fulfi lls all
the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I.
2012/3032 (as amended) and that the following designated
standards have been used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-22:2011+A11:2013
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN 61000-3-3:2013
BS EN IEC 63000:2018
Winnenden, 2020-12-15
20 ENGLISH
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

ADVICE FOR OPERATION

The speed of rotation is adjusted electronically when the
load increases.
In case of a longer overload period the speed is decreased
electronically. The machine continues to run slowly to cool
down the motor coil. After switching off and on the machine
can be used at rated load.
Under the eff ect of extreme electromagnetic interferences
from the outside, temporary variations in the speed of
rotation could arise in particular cases.
Sharpen blunt diamond cutting blades (can be recognised
by sparks fl ying while cutting) by making several cuts into
calcareous sandstone or a special sharpening stone.
The cutting discs get very hot when in use. Do not touch
them before they have cooled down.
MAINTENANCE
The ventilation slots of the machine must be kept clear at
all times.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the
six-digit No. on the label and order the drawing at your
local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Wear ear protectors!
Use an FFP2 particulate respirator as the
minimum amount of protection.
Wear gloves!
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Class II tool, tool in which protection against
electric shock does not rely on basic
insulation only, but in which additional safety
precautions, such as double insulation or
reinforced insulation, are provided.
There being no provision for protective
earthing or reliance upon installation
conditions.
European Conformity Mark
British Confomity Mark
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Ukraine Conformity Mark
EurAsian Conformity Mark
21