Page 1
All manuals and user guides at all-guides.com [USER MANUAL]...
Page 2
DEUTSCH ENGLISH FRANÇAIS All manuals and user guides at all-guides.com DEUTSCH Belinea 10 60 55 DEUTSCH 2 ~ 10 ENGLISH 11 ~ 18 FRANÇAIS 19 ~ 26 Bedienungsanleitung - 1...
Systeme verarbeitet, vervielfältigt oder verbreitet werden. Stromsparfunktionen ..........10 Änderungen, die dem technischen Fortschritt dienen, blei- Technische Daten ............ 10 ben vorbehalten. Belinea ist ein international eingetragenes Warenzeichen. Andere Markennamen können eingetragene Warenzeichen sein und müssen als solche behandelt wer- Stiftbelegung des Signalsteckers ......10 den.
Elektrizität der Bild- schirmoberfläche entladen kann. Die Netzsteckdose sollte sich in direkter Nähe befinden und leicht zugänglich sein. Der Moni- tor kann nur durch Ziehen des Netzsteckers aus der Steckdose ganz vom Netz getrennt werden. 4 - Belinea 10 60 55...
Abbildung 2. Monitor an den PC anschließen EINSCHALTEN 1. Schalten Sie zuerst den PC und anschließend den 3. Wird auf dem Monitor kein Bild angezeigt, lesen Belinea-Monitor ein. Die Betriebsanzeige (siehe Sie die Informationen im Abschnitt „Problemlösun- in Abbildung 4) leuchtet grün auf. gen”.
Betrieb zu nehmen, wird dringend empfohlen, die Belinea-Einstellungsdatei zu installieren. Sie können Monitor unter Windows NT 4.0 konfigurieren: diese über Ihren Belinea-Händler beziehen oder von Unter Windows NT 4.0 benötigen Sie keine separate der Belinea-Website www.belinea.de laden. Wählen Einstellungsdatei. Wählen Sie die Bildwiederhol-...
All manuals and user guides at all-guides.com DEUTSCH FUNKTIONEN DES OSD-MENÜS POSITION LANGUAGE Wählt die Sprache des OSD-Menüs: Englisch, Deutsch, Regelt die horizontale Position des Französisch, Spanisch, Italienisch. Bildes. Regelt die vertikale Position des Bildes. OSD POSITION Regelt die horizontale und vertikale Lage des OSD- SIZE Menüs.
All manuals and user guides at all-guides.com DEUTSCH PROBLEMLÖSUNGEN Kein Bild Netzanzeige leuchtet nicht Prüfen Sie, ob das Netzkabel richtig angeschlossen ist (siehe Abschnitt „Anschließen”). Stellen Sie sicher, daß der Monitor mit dem Netzschalter eingeschaltet wurde (siehe Abschnitt „Einschalten”). Netzanzeige leuchtet orange oder blinkt Befindet sich der Monitor in einem Stromsparmodus (siehe Abschnitt „Stromsparfunktionen”)? Ist das Signalkabel am Monitor und an der VGA-Buchse des PC angeschlossen? Ist der PC eingeschaltet (siehe Dokumentation zu Ihrem PC)?
INTRODUCTION TABLE OF CONTENTS This manual will familiarize you with the installation and Introduction .............. 11 use of your Belinea Monitor. Please take the time to Features ..............12 look through these instructions even if you are familiar with monitors.
The monitor may only be opened and serviced to dissipate. by qualified professionals. The wall outlet should be within easy reach. Pulling the power plug is the only way to disconnect the monitor from the power source. 12 - Belinea 10 60 55...
Figure 3. Connecting the monitor to the power source Figure 2. Connecting the monitor to the PC STARTUP 1. First, turn on your PC, and then turn on your Belinea 3. If there is no image displayed on the monitor, ...
For Windows 95/98 and 2000 users: Installation of the Belinea driver software is highly recommended. This Monitor setup under Windows NT 4.0: can be obtained from your Belinea dealer or downloaded Under Windows NT 4.0 no separate setup file is from Belinea’s internet homepage at www.belinea.de.
All manuals and user guides at all-guides.com ENGLISH OSD MENU FUNCTIONS POSITION LANGUAGE Selection of the OSD menu language: English, German, Controls the horizontal position. French, Spanish, Italian. Controls the vertical position. OSD POSITION SIZE Adjusts the vertical and horizontal position of the OSD menu.
All manuals and user guides at all-guides.com ENGLISH TROUBLESHOOTING Blank Screen Power indicator is off Check if the power cable is connected properly (see section “Connecting”). Make sure that the monitor was turned on using the power switch (see section “Startup”). Power indicator lights orange or is flashing Perhaps a power saving mode is active (see section “Energy Saving Functions”)? Is the signal cable connected to the monitor and the PC’s VGA connector?
Résolution des problèmes ........25 Nous nous réservons le droit d’apporter des modifications Fonctions de gestion de l’énergie ......26 motivées par le progrès technique. Belinea est une marque internationalement déposée. Les autres marques et noms de Specifications techniques ........26 produits mentionnés dans ce document peuvent être des...
Ce délai est nécessaire pour permettre à l’électricité statique de se dissiper. La prise d’alimentation murale doit être aisément accessible. La seule façon de débrancher le moniteur de la source d’alimentation électrique consiste à débrancher le cordon secteur. 20 - Belinea 10 60 55...
électrique MISE EN ROUTE 1. Mettez d’abord votre PC sous tension, puis allumez 3. Si aucune image n’apparaît sur le moniteur, votre moniteur Belinea à l’aide de son interrupteur. consultez la section ”Résolution des problèmes”. L’indicateur d’état (voir à...
Installation du moniteur sous Windows 4.0: de votre revendeur Belinea, ou le télécharger en rendant visite à la page d’accueil du site Web de Belinea, à Sous Windows NT 4.0, il n’est pas nécessaire d’utiliser www.belinea.de. Cliquez ensuite tour à tour sur les liens un fichier d’installation séparé.
All manuals and user guides at all-guides.com FRANÇAIS FONCTIONS DU MENU OSD POSITION LANGUAGE Sélection du langage utilisé pour le menu OSD: Anglais, Permet de régler la position Allemand, Français, Espagnol, Italien. horizontale Permet de régler la position verticale. OSD POSITION Réglage de la position vertical e et horizontale du menu SIZE OSD.
All manuals and user guides at all-guides.com FRANÇAIS RÉSOLUTION DES PROBLÈMES Écran noir L’indicateur de mise sous tension est éteint Regardez si le câble d’alimentation secteur est correctement raccordé (voir la section ”Raccordement”). Vérifiez que le moniteur a été allumé à l’aide du bouton de mise sous tension (voir la section ”Mise en route”). L’indicateur de mise sous tension est allumé...
BROCHAGE Broche Fonction Broche Fonction Rouge — Vert Terre Bleu Terre Terre Signal SDA Connecteur 15 broches ; type Mini D-sub Synchro horizontale Terre Retour rouge Synchro verticale Retour vert Signal SCL Retour bleu 26 - Belinea 10 60 55...