Publicité
Liens rapides
Dee Zee Britetread Side Mount Toolbox
This toolbox installation instruction is for both Single-Lid Toolboxes and Double-Lid Toolboxes.
Cette instruction d'installation de boîte à outils est pour des boîtes à outils de Single-Lid et des boîtes à outils
de Double-Lid.
A
Britetread Side Mount Toolbox:
Toolbox lid design may vary from picture with different toolbox models.
Boîte à outils De Support De Côté De Britetread:
La conception de couvercle de boîte à outils peut changer de l'image
avec différents modèles de boîte à outils.
B
Mounting Bracket
X2
G
1/4 x 1" Sheet
Metal Screw
Black
X4
L
TB-Channel
X6
Tools Required:
Outils Necessaires:
Deezee-sidemount-tb.p65
Installation Instructions
C
Mounting Bracket
X2
H
1/4 x 1" Sheet
Metal Screw
X8
M
TB-Divider
X3
7/16"
D
Foam
Tape
X2
I
3/8 x 1" Buttom Head
Screw
X6
N
CO-Tape
X18
1/4"
03/20/2000
E
F
1/4" Flat Washer
Black
X4
K
J
3/8" Locknut
X6
X1
3/8" Flat Washer
Black
X6
Plastic Plug
X2
Page 1
Publicité
Manuels Connexes pour Dee Zee Britetread DZ91
Sommaire des Matières pour Dee Zee Britetread DZ91
- Page 1 Dee Zee Britetread Side Mount Toolbox Installation Instructions This toolbox installation instruction is for both Single-Lid Toolboxes and Double-Lid Toolboxes. Cette instruction d'installation de boîte à outils est pour des boîtes à outils de Single-Lid et des boîtes à outils de Double-Lid.
- Page 2 Use the pictures to the right as a guide in locating the britetread side mount toolbox (A). Note: If the britetread side mount toolbox (A) is to be installed with a front mount toolbox (As shown in Drawings B and C), be sure to leave enough space between the toolboxes to allow clearance to open both toolbox lids.
- Page 3 Hold the britetread side mount toolbox (A) level while positioning mounting brackets (B / C) as shown below. Once the brite- tread side mount toolbox (A) is level and the mounting brackets (B /C) are in the desired position, use a pair of vise-grips to hold them together.
- Page 4 Optional: Britetread side mount toolbox (A) - Divider installation instructions Peel the backing off of each piece of CO-Tape (N) and then place the CO-Tape pieces (N) onto the back of each TB-Channel (L) as shown below. Now determine exactly where you would like to place the toolbox dividers. Note: There are only three TB-dividers (M) supplied with the britetread side mount toolbox (A).
-
Page 5: Cleaning Instructions
Dee Zee does not insure loss of contents. After drilling, Dee Zee recommends putting a sealant or rust inhibitor around all holes drilled into the body panel of the vehicle. If you should incur any problems with the installation of this product, please feel free to call us at 1-800-779-8222. So that we may better serve you when you call, please have the W/O#, SEQUENCE#, and the DATE from the label on the outside of the box. -
Page 6: Ordering Replacement Parts
Part Number: TB85614 Ordering Replacement Parts: Ordering replacement parts for your Dee Zee single-lid / double-lid toolbox is fast, convenient, and easy. Just call our customer service phone number at 1-800-779-2102 for pricing and ordering information. Please provide the customer service reprentative with the part number from the above parts list.