Features And Specifications; Power Output - Jensen power POWER 400 Manuel D'installation Et Operation

POWER Amplifiers

Features and Specifications

Your new Jensen Power mobile stereo power amplifier is the amplifier of
choice for the high demands of auto sound reproduction. With its deep-bass
reproduction and plenty of reserve power, low harmonic distortion and neutral
reproduction, the Power series of amplifiers takes Mobile Hi-Fi to new heights.
Like all Jensen products, when it comes to accurate sound reproduction the
Power series takes a back seat to no one. Jensen will bring your Hi-Fi
experience to new heights with the following features:
• MOSFET Power Supply
• High Current Bi-Polar Output Transistors
• Optimized Class B Design Minimizes Distortion and Reduces Idle Current
• Easily Drives 2-Ohm Loads
• Pass-Thru RCA's
• Variable Bass EQ 0 - 12dB @ 45 Hz
• 12dB / Octave Low Pass and High Pass filters
• Variable Input Level 400mV - 5V
• Short Circuit, DC-offset and Thermal Overload Protection Circuitry
• Diagnostic LED's - Green: Power, Red: Standby / Fault
Power 400 / 760 / 880 / 920
• Low Pass Filter 40 - 300 Hz
• High Pass Filter 40 - 300 Hz
• High Pass / Low Pass / Full Range Selector Switch
• Stereo / Mono Mode Switch (Power 400 and 880 only)
• 2/ 3 / 4 Channel Mode Switch (Power 760 and 920 only))
Power 900 / 1050
• Mono Subwoofer Amp
• Low Pass Filter 40 - 240 Hz (Power 900)
• Low Pass Filter 40 - 150 Hz (Power 1050)
• Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900)
• Subsonic Filter 15 - 55 Hz, 12dB / octave (Power 1050)
• Remote Input Level Control (Remote Bass Control) w/ 5 Meter Interface
Cable
Specifications
Power 400 / 760 / 880 / 920
• Load Impedance: 2 / 4-Ohm
• Signal to Noise @ 1 kHz: >100dB (rated power)
• Channel Separation @ 1 kHz: >60dB
• Frequency Response: 5-60 kHz, -3dB
• Input Impedance: 20 kHz, nominal
• THD+N @ 5 Watts: 0.02%, 1 kHz, 14.4VDC
Power 900 / 1050
• Signal to Noise @ 120 Hz: >100dB (Rated Power)
• Channel Separation Not Applicable
• THD+N @ 5 Watts: 0.02%, 125 Hz, 14.4VDC

Power Output

RMS Power Output @ 2% THD+N, 1kHz, 14.4VDC
Power 400
• 75 x 2 Watts, 4-Ohm
• 100 x 2 Watts, 2-Ohm
• 200 x 1 Watts, 4-Ohm Bridged
Power 760
• 75 x 4 Watts, 4-Ohm
• 100 x 4 Watts, 2-Ohm
• 190 x 2 Watts, 4-Ohm Bridged Stereo
Power 880
• 135 x 2 Watts, 4-Ohm
• 220 x 2 Watts, 2-Ohm
• 440 x 1 Watts, 4-Ohm Bridged
Power 900
• 300 x 1 Watts, 4-Ohm
• 450 x 1 Watts, 2-Ohm
Power 920
• 100 x 4 Watts, 4-Ohm
• 140 x 4 Watts, 2-Ohm
• 230 x 2 Watts, 4-Ohm Bridged Stereo
Power 1050
• 350 x 1 Watts, 4-Ohm
• 525 x 1 Watts, 2-Ohm
Specifications subject to change without notice.
2