Using The Headset; Led Indication; Battery Usage - SBS TEEARSETBT320K Mode D'emploi

UK
Before you start using the headset, you must charge the
battery and pair the headset with a compatible phone.
Thank you for buying the SBS Bluetooth® Headset. The Headset
gives you crisp clear voice calls while keeping your hands free so
you are able to drive safely, exercise or work and still receive phone
calls. The Headset is compatible with many Bluetooth® devices
such as Apple iPad, iPhone, iPod Touch, Android smartphones,
laptops, PC, and gaming consoles as well as Skype. Please read
this user guide carefully so that you understand the setup and
usage procedure.
CONNECT THE HEADSET WITH BLUETOOTH® DEVICE
To connect and pair the SBS Handsfree Bluetooth® Headset with a
Phone or Tablet Please follow this procedure.
1. Put the Headset into Connect mode by holding the Multi-function
button for 7 seconds. The LED will flash alternately Red/Blue to
show it is looking for a Bluetooth® device to connect with.
2. Go to the Bluetooth® settings on your Phone/tablet and look for
SBS. Select that and the Headset will be connected. Note: Some
phones will ask for a PIN code, simply enter "0000" and the
Headset will be connected.
3. When the Headset is connected the LED will flash Blue every 7
seconds to indicate it is connected.
4. NFC Pairing-only for NFC enabled phones. Power on state, put
the mobile phone NFC touch with the Bluetooth® headphone NFC,
the headphone will be connected automatically.

USING THE HEADSET

Make a call: simply dial the number on the Phone and the call will
be automatically connected to the Headset.
Answer a call: when there is an incoming call, just push the multi-
function button.
End a Call: to end call just push the multi-function button.
Reject a call: hold down the multi-function button for 3 seconds
4
and you'll hear a beep from the Headset.
Voice Dialling: hold down the multi-function button and VOL button
until you hear a beep. Just Speak the name of the person you wish
to call loudly and that number will be automatically called.
Note: be sure your phone supports this function and it is enabled.
Redial: double press the multi-function button until you hear a
beep, and the last number called will be redialled.
Mute: press the VOL button for 3 seconds and the Headset will
mute the Microphone. Press the VOL button again to activate the
microphone.
Volume Adjustment: press the Vol button, the sound will be louder
until you hear a beep, it is the max, and then the sound will be lower,
until you hear the beep, it is lowest sound. It will cycle all the time.
Switch the call between mobile and headset: in call State, press
the multi-function button for 3 seconds, the call will be switched to
Mobile, the same action, the call will be swtiched to the Bluetooth®
device.
Play / Pause music: when in stand-by mode, press the multi-
function button for play/pause music. When playing music, press
VOL button for 3 seconds to play the next song.

LED INDICATION

1. Power on: press the multi-function button for 3 seconds, blue
light flashes 3 times.
2. Power off: press the multi-function button for 3 seconds, red
light flashes 3 times.
3. Stand-by (not connected): blue light flash one time every 5
seconds.
4. Standby (connected): blue light flash 1 time every 5 seconds.
4. Pairing: blue and red light flash alternatively.
5. Incoming call: blue light flash quickly twice every 2 seconds.
7. Charging: red light flash long.
8. Full charged: red light die out.
9. Low voltage alarm: red light flash one time every minute.

BATTERY USAGE

When the Battery is fully charge the talking time is up to 4 hours,
the stand-by time is 200 hours. When the battery is low the Red
LED will flash one time every 6 seconds. Please recharge at this
time.
5