Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: Pullwires (provided), Masking tape, Small
screwdriver, Paint
Fastener Kit: 24874F
Wrenches: 11/16", (2) 3/4"
Drill Bits: 3/8" or 1" Hole Saw or cutting tool
B. Align block on
A. Insert bolt and
access hole
Block into frame
Figure 4
Access hole modification to allow
pullwire of spacer and carriage bolt
Figure 2
Figure 2
Note: sort hardware prior to hitch installation to confirm 1/2" &
7/16" conical washer are kept with coordinated 1/2" & 7/16" bolts.
1
Qty. (1)
U-bolt 3/8-16"
2
Qty. (2)
Flat washer 3/8"
3
Qty. (2)
Lock washer 3/8"
4
Qty. (2)
Hex nut 3/8-16
5
Qty. (1)
Bolts ½-13 X 1.75 GR5
6
Qty. (1)
Spacer ¼" X 1" X 1-1/2"
1.
Remove the (2) plastic rivets that fasten the fascia tabs to the trunk pan. Note: Remove the center of the rivet with a screwdriver and remove
remaining piece. Rivets to be reinstalled. Carefully push fascia toward the impact bar and out of the way.
2.
Enlarge the forward access hole or drill 1" access hole in bottom of passenger side frame rail between the attachment holes for bolts and
spacers. See enlarge method Figure 2. Paint any exposed metal
3.
Feed spacers and carriage bolts into position using the pull wires provided. Leave pull wire attached. Note: It is much easier if bolt and spacer
are not engaged while inserting them into frame, refer to illustration. See Figure 3 & 4.
4.
Pull heat shield away from end panel to allow access for hitch upright bar. Note; use tape on heat shield due to sharp edges.
5.
Hang u-bolt on tow hook.
6.
Raise hitch into position at the tow hook. Maneuver the upright bar between the end panel behind the heat shield. Attach flat washer, lock
washer and hex nut. Leave fasteners snug.
7.
Feed the pull wires through the slots of the passenger side bracket. Shift the bracket into location as shown. Pull the fasteners though the
bracket. Remove one pull wire at a time (being careful not to push the fasteners into the frame rail) and attach the conical washer and hex nut as
shown. Repeat with remaining fastener.
8.
Insert the ½-13 bolt into the spacer, reaching behind the end panel insert the bolt through the hole in end panel and slot in upright bar and attach
the conical washer and hex nut. Orientate the spacer as shown.
9.
Tighten all fasteners to the required torque specification.
10. Reattach the fascia back into position from step 1.
11
11. Push heat shield back into position.
Push heat shield back into position
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2011 Cequent Performance Products
Installation Instructions
Fascia
Drawbar must be used in the
Rise position only.
se pos t o o y.
End
panel
C. Pull bolt thru
block
Kink pull wire
to keep block
independent of
bolt
Figure 3
Fi
3
Mazda 5
Drawbar Kit:
3592
7 8
Gently bend heat shield
away from end panel not
shown
shown
6
5
Upright
1
bar
2
3
3
4
7
Qty. (1)
8
Qty. (1)
9
Qty. (2)
Qty. (2)
11
Qty. (2)
12
Qty. (2)
Tighten all 3/8-16 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing
Vehicle Manufacturer's Rating or
Vehicle Manufacturer s Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Drill 1" access hole or
enlarge existing hole
Frame rail
Tow hook
Figure 1
Conical washer ½"
Hex nut ½-13
Carriage bolt 7/16-14 X 1-3/4" GR5
Spacer ¼" X 1" X 3"
Conical washer 7/16"
Hex nut 7/16-14
24874N
6-14-11
Part Numbers:
24874
60291
77246
9
9
Enlarge
access
hole
11
12
Rev. A
Form F206 Rev A 5605
Publicité
Manuels Connexes pour Cequent Performance Products 24874
Sommaire des Matières pour Cequent Performance Products 24874
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24874N 6-14-11 Rev. A 2011 Cequent Performance Products Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24874N 6-14-11 Rev. A 2011 Cequent Performance Products Form F206 Rev A 5605...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 24874N 6-14-11 Rev. A 2011 Cequent Performance Products Form F206 Rev A 5605...