Before First Use; Using The Device - Adler europe AD 7740 Mode D'emploi

19. Place the fan heater only on flat, stable surface.
20. Always turn the fan heater off and set the thermostat dial to minimum before removing
the power plug from the socket.
21. Never use the fan heater in high humidity rooms – bathroom, shower room, swimming
pools etc. The humidity can cause short circuit, and effect in damaging the device.
22. The operating fan heater needs to be under supervision and in sight all the time. If you
are leaving the room with the fan heater, always turn the fan heater off. If the fan heater is
not used, the power plug has to be removed from the power outlet.
23. Do not connect the fan heater to the automatic switching device, for example
temperature controlling device or time switch.
24. Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should
be kept at least one meter from the fan heater.
25. Do not cover the device or put any objects on it while it is operating. Do not use the
device to dry clothes.
26. The power cord should not be placed above the fan heater, and it should not touch or
be placed near hot surfaces of the fan heater. Do not place the fan heater directly under
the power outlet.
27. The heating surfaces can heat to a temperature of 60 °C or higher. The fan heater
should be in a place that children and animals do not have access to.
28. The device is not intended to be installed or used in vehicles.
29. Some parts inside the device can be hot or cause sparking. Do not use the fan heater in
places, where gasoline, paints or other flammable materials are used or stored.
30. Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
31. Do not use this heater if it has been dropped
32. Do not use if there are visible signs of damage to the heater
33. Use the heater on a level and stable surface or attach it to the wall, if provided for by the
manufacturer
WARNING: Do not use this heater in small rooms where there are people who are unable to
leave them by themselves, unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at
least 1 m away from the heater air outlet.

BEFORE FIRST USE

1. Place the device on even, flat surface. Position it a minimum 1 meter distance from the air inlet (3) and air outlet (4) to allow a good
airflow circulation. The device should not be placed underneath a power outlet. Plug in the device to suitable socket.
2. When the heater is turned on for the first time, it may release a slight, harmless odor. This odor is a normal occurrence caused by the
initial heating of the internal heating elements and should not occur again.
DESCRIPTION OF THE DEVICE: CERAMIC FAN HEATER
1. Thermostat knob
3.Air inlet
5.Handle

USING THE DEVICE

To switch on the device turn the thermostat knob from position zero (0) to position one (I), just the fan is switched on, unheated air flow is
available.
1) Turn the thermostat knob in a clockwise direction until it reaches the maximum setting.
2) Set up required heating power level (1000W or 2000W or 3000W). Read point 5).
3) When the room has reached the required temperature turn the thermostat knob (1) in an counterclockwise direction up to the point
where the device switches off and not beyond. The temperature fixed in this way will be automatically controlled and kept at a
constant .
4) The temperature of heating can be adjusted on each heating power level by using the thermostat knob (1) by rotation between MIN and
MAX according to your requirements.
5) To switch on one or both sections of heating elements you must use the push button switches (2).
Change the position of the push button switch from position zero (0) to the position one (I – button pressed down) to switch on the heating
power.
-The push button switch marked by 1000W switched on the heating element with power 1000W.
-The push button switch marked by 2000W switched on the heating element with power 2000W.
-Simultaneous pushing of two push button switches marked by 1000W and 2000W together will switched on both sections of the heating
elements with power 3000W.
2.Push button switches
4. Air outlet
7