Westin Automotive Products 30-0000 Instructions

AUTOMOTIVE PRODUCTS, INC.
SAFARI BAR ASSEMBLY
BARRA PARA PARRILLA SAFARI
MONTAGE DE LA BARRE PARE-
CHOCS SAFARI
30-0000 30-0005
MOUNT KIT
EQUIPO DE MONTAJE
JEU DE MONTAGE
30-1255
ITEM QTY
1 1 SAFARI BAR ASSEMBLY (PURCHASED SEPARATELY)
2,3 2 BRACKET, PASSENGER (2) AND DRIVER(3)
4 2 1/2-13 X 2.00" HEX HEAD BOLT
5 6 1/2" FLAT WASHER
6 2 1/2" LOCK WASHER
7 2 3/8-16 X 1.00" HEX HEAD BOLT
8 4 3/8" FLAT WASHER
9 2 3/8" LOCK WASHER
10 2 3/8-16 HEX NUT
11 2 10MM PUSH TYPE RETAINER
12 2 8MM PUSH TYPE RETAINER
1 1 BARRA PARA PARRILLA SAFARI (SE COMPRA SEPARADO)
2,3 2 SOPORTE, ACOMPAÑANTE (2) Y CONDUCTOR (3)
4 2 PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 2,00"
5 6 ARANDELAS PLANAS DE 1/2"
6 2 ARANDELAS DE PRESIÓN DE 1/2"
7 2 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,00"
8 4 ARANDELAS PLANAS DE 3/8"
9 2 ARANDELAS DE PRESIÓN DE 3/8"
10 2 TUERCAS HEXAGONALES DE 3/8-16
11 2 RETENES DE 10 MM A PRESIÓN
12 2 RETENES DE 8 MM A PRESIÓN
1 1 MONTAGE DE LA BARRE PARE-CHOCS SAFARI (ACHETE SEPAREMENT)
2,3 2 SUPPORTS, PASSAGER
4 2 BOULON A TETE HEXAGONALE DE 1/2-13 X 2,00 PO
5 6 RONDELLE PLATE 1/2 PO
6 2 RONDELLE A FREIN DE 1/2 PO
7 2 BOULON A TETE HEXAGONALE DE 3/8-16 X 1,00 PO
8 4 RONDELLE PLATE 3/8 PO
9 2 RONDELLE A FREIN DE 3/8 PO
10 2 ÉCROUS HEXAGONAUX 3/8-16
11 2 PUNAISE 10MM
12 2 PUNAISE 8MM
STEP 1. Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before begin-
ning.
STEP 2 Determine passenger and driver brackets.
.
STEP 3 Remove 16 push type retainers from lower splash shield. Remove plastic splash shield to gain access to mounting locations.
.
STEP 4. Locate and remove fasteners that hold frame brace and bumper brackets to vehicle using a 17mm and 14mm socket and
SEE FIGURE 1.
ratchet.
STEP 5. Install brackets between lower radiator support and top of frame brace using (2) 1/2" flat washers on top of bracket's frame brace
slots and existing bolts previously removed. Install using 3/8" fasteners per bracket.
loosen body mount bolt holding frame brace to gain enough clearance to slide brackets in place.
STEP 6. Temporarily attach the Safari Bar using 1/2" fasteners as shown.
Recommended torque values are 26 Ft. Lbs. for 3/8" fasteners, 35 Ft. Lbs. for 10mm fasteners, and 61 for 12mm fasteners.
STEP 7. Remove Safari Bar.
STEP 8. Cut plastic splash shield to accommodate brackets. See cutting reference for guidelines on cutting.
STEP 9. Re-install splash shield and all push type retainers.
STEP 10. Re-attach Safari Bar.
The template works best if placed on the top side of the splash shield (the side towards the vehicle). Locate two oval slots that measure 3
3/8" x 1 3/16". Cut out template and place over the appropriate slots. Hold in place using masking tape. Drill 1/4" holes at each of the small
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2003-08 HONDA PILOT
APLICACIÓN: HONDA PILOT, MOD. 2003-08
APPLICATION: HONDA PILOT 2003-08
CONTENTS - CONTENIDO
(2) ET CONDUCTEUR
Level and adjust Safari Bar as desired and tighten 1/2" fasteners to 64 Ft. Lbs.
CUTTING INSTRUCTIONS
- (Recommendation only, sizes are approximate)
- CONTENU
(3)
Level and adjust Safari Bar as desired and tighten all fasteners.
WO:
TOOLS - HERRAMIENTA
3/4" WRENCH
9/16' SOCKET
9/16" WRENCH
17MM SOCKET
17MM WRENCH
14MM SOCKET
14MM WRENCH
RATCHET
SMALL FLAT SCREWDRIVER
TORQUE WRENCH
UTILITY KNIFE
LLAVE DE TUERCAS 3/4"
DADO DE 9/16"
LLAVE DE TUERCAS DE 9/16"
DADO DE 17MM
LLAVE DE TUERCAS DE 17MM
DADO DE 14MM
LLAVE DE TUERCAS DE 14MM
MANERAL
DESTORNILLADOR DE PUNTA PLANA PEQUEÑO
LLAVE DE TORQUE
NAVAJA
CLE 3/4 PO
DOUILLE 9/16 PO
CLE 9/16 PO
DOUILLE 17MM
CLE 17MM
DOUILLE 14MM
CLE 14MM
CLIQUET
PETIT TOURNEVIS A BOUT PLAT
CLE DE COUPLE
COUTEAU
SEE FIGURE 1. NOTE:
It may be necessary to
75-0352 REVISION B 12/7/07
- OUTILS