Getting Started - Bellman & Symfon Maxi Pro Mode D'emploi

Overview
1
Charger jack
2 Microphone
indicator
3 On/Off
4
Microphone
selector
5 Volume/tone
indicator
6 Volume
controls
7 Tone
controls
8 Battery
indicator
About Maxi Pro
Maxi Pro is a digital conversation amplifier that
brings out the words so you can hear them
loudly and clearly. Use Maxi to enhance the
speech around the table, when you talk on the
mobile phone or when you watch TV.

Getting started

Step 1: Charge Maxi
1 Connect the charging cable to the power
adapter (13) and to the charger jack (1)
marked in yellow.
5
13 Power adapter
9
Microphone
10 Bluetooth indicator
11 Bluetooth selector
12 Headphone jack 14 Mains plug
Appearance and function
may vary with package
2 Fit the mains plug (14) to the power
adapter (13) and connect it to the power
outlet.
3 The battery indicator (8) blinks in green
during charging. After about three hours
it emits a steady green light to show that
that Maxi is fully charged.
Step 2: Connect Maxi
Connect the supplied headphones, ear-
phones, headset, earset or neck loop to the
Maxi headphone jack (12) marked in green.
Step 3: Start Maxi
Press the On/Off button (3) for about one
second to start Maxi. The microphone
indicator (2) lights up in green and the cur-
rent volume is shown by the volume/tone
indicator (5) for three seconds.
To switch Maxi off, press and hold the On/
Off button (3) for about three seconds until
all indicators go out.
Using Maxi to
clarify speech
Maxi is equipped with a built in omni-di-
rectional microphone (9) that enhances
speech. Place Maxi on a table close to the
person talking, hold it in your hand or
attach it to your clothes using the clip.
Adjusting the volume
Press on the volume controls (6) to
increase the volume and to decrease it.
The microphone volume can be adjusted
in 9 steps and the TV and mobile phone
volume in 15 steps. The level is shown in
the volume/tone indicator (5).
Note: Every time you turn on Maxi, the
volume is set to low to avoid unpleasant
sound levels .
Adjusting the tone
Press the on the tone controls (7) to
increase the treble and the to decrease
it. The treble can be adjusted in 5 steps and
is visible in the volume/tone indicator (5).
Note:
Increasing the treble makes the S, F
and T sounds more pronounced and the
words easier to make out.
Using Maxi with
your mobile phone
Pairing
1
Make sure your Maxi is in microphone mode
by pressing the microphone selector (4).
2
Press and hold the Bluetooth selector
(11) until the Bluetooth indicator (10)
starts to blink in blue.
3 Make sure Bluetooth is activated on
your mobile phone. Open the Bluetooth
menu in Settings and select "Maxi Pro" in
the list.
4 The Bluetooth indicator will emit a steady
blue light to show that the pairing was
successful.
Note: If your phone has been disconnected
from Maxi, you might need to reconnect it
by repeating step 3 to 4.
Answering a phone call
1
When the mobile phone rings, the Maxi
Bluetooth indicator (10) blinks in blue. All
other sounds are muted and you'll hear
the ring signal in your headphones.
2 To answer the call, press the Maxi
Bluetooth selector (11) or use the remote
on your headset. You will now hear the
enhanced voice of the caller in your
headphones. Your voice will be picked up
by the headset or the Maxi microphone.
3 To hang up, press the Bluetooth selector
once more.
Note: To decline an incoming call, press
and hold the Maxi Bluetooth selector for 3
seconds.
Making a phone call
When you talk on the mobile phone, you
hear the enhanced voice of the recipient in
your headphones. Your voice will be picked
up by the Maxi microphone.
Streaming music
Play a song on your mobile phone and press
the Maxi Bluetooth selector (11) to hear the
music. A second press could be needed if
another Bluetooth source also is connected.
Using a headset with microphone
When you talk over the phone, the sound
will be picked up from the headset remote
microphone instead of the Maxi microphone.
EN
6