Adjusting; Folding Instructions; Training With Heart Rate; Maintenance - virtufit Trendline Loopband Mode D'emploi

ENGLISH
Hex head bolts: Make sure that the hex head spanner is pushed into
the bolt before applying force. This will prevent the head of the socket
bolt from turning.

FOLDING INSTRUCTIONS

FOLDING INSTRUCTIONS
FOLDING INSTRUCTIONS

ADJUSTING

INKLAP INSTRUCTIES
INKLAP INSTRUCTIES
INKLAP INSTRUCTIES
NOTE:
OTE: Store your machine in a dry area away from children and high tra c areas as shown in the
Store your machine in a dry area away from children and high tra c areas as shown in the
NOTE:
Store your machine in a dry area away from children and high tra c areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
stration. Be sure it is secure and cannot fall onto small animals or children.
Adjusting
illustration. Be sure it is secure and cannot fall onto small animals or children.
1. The treadmill veers to the left: Turn on the treadmill, set the
speed to 2 to 3 km/h without forcing. Use the Allen key to turn
the screw on the left side of the end of the treadmill a quarter
turn to the right (1). Run the treadmill for 1 to 2 minutes without a
load. Repeat the process until the treadmill is exactly in the
middle.
2. The treadmill turns to the right: start the treadmill, set the
speed to 2 to 3 km/h without a load on the treadmill. Using the
hexagonal key, turn the screw on the right side of the end of the
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and
-- Pull the pull-pin on the console handrail to fold the console carefully.
1. Pull the pull-pin on the console handrail to fold the console carefully. Pay attention to the cables and -- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pull the pull-pin on the console handrail to fold the console carefully.
-- Pay attention to the cables and ensure that they are nog pinced. treadmill a quarter turn to the right (2). Run the treadmill for 1 to
-- Pay attention to the cables and ensure that they are nog pinced.
ensure that they are nog pinced.
ensure that they are nog pinced. -- Pay attention to the cables and ensure that they are nog pinced.
ensure that they are nog pinced.
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
--unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up. 2 minutes without a load.
Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
--Place the machine leaning against the wall or place under a bed.
--Place the machine leaning against the wall or place under a bed.
2. Unscrew the hand knob on the both sides of the frame respectively and carefully fold the console up.
--Place the machine leaning against the wall or place under a bed.
3. Place the machine leaning against the wall or place under a bed.
3. The treadmill has jammed: Use the Allen spanner to turn the
Place the machine leaning against the wall or place under a bed.
3. Place the machine leaning against the wall or place under a bed.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
CAUTION: Do not allow children to touch the machine, the treadmill may fall.
screw on the right side of the end half a turn to the right and
RUNNING BELT ADJUSTMENT
RUNNING BELT ADJUSTMENT
RUNNING BELT ADJUSTMENT
the screw on the left side of the end half a turn to the right as
well. Repeat the process until the blockage is resolved (3).
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
01. Running belt deviates to left: Start the machine, set speed at 2-3 km/h without a load on the belt,
Adjust inclination
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
e Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
use Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
minutes. Repeat process until the belt becomes central.
nutes. Repeat process until the belt becomes central.
minutes. Repeat process until the belt becomes central.
There are incline blocks on both sides of the treadmill. It has a slope of
3 levels. Use the pins to adjust the slope level adjust.
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
02. Running belt deviate to right: Start the machine, set speed at 2-3 km/h without a load on the belt,
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
e Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
use Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2
NOTE!
minutes. Repeat process until the belt becomes central. The pins should have the same position for both sides while
nutes. Repeat process until the belt becomes central.
minutes. Repeat process until the belt becomes central.
11
11
adjusting the slope.
11
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
03. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a
turn both left and right until the jam solved (see fig 3).
n both left and right until the jam solved (see fig 3).
turn both left and right until the jam solved (see fig 3).
Virtufit Totally Foldable TR-50i Treadmill
otally Foldable TR-50i Treadmill
fit Totally Foldable TR-50i Treadmill
FOLDING INSTRUCTIONS
NOTE!
Store the Folding Exercise Bike in a dry place, out of reach
of children, as shown in the diagram. Make sure the folding exercise
NL
NL
NL
EN
EN
EN
bike is stable and secure to prevent it from falling on pets or children.
Folding
• Loosen the Locking Knob (24) and pull the Adjuster downwards.
• Lift the treadmill up towards the frame to fold the treadmill
• Secure the treadmill to the frame by tightening the Side Knob
(25) on the left upright tube
Unfolding
• Loosen the Side Knob (25) on the left upright tube.
• Unfold the treadmill by pushing the treadmill downwards.
• Pull up the Adjuster and tighten the Locking Knob (24) to lock
the treadmill in the correct position.
SAFETY KEY
Remove the safety key for an emergency stop. The treadmill stops
slowly and "Err" appears on the display. Replace the safety key and the
display shows "OFF".

TRAINING WITH HEART RATE

Hand sensors
This VirtuFit fitness machine is equipped with hand sensors to measure
heart rate. The hand sensors are attached to the handle and only work
if both sensors are held for a long time. For optimal performance, it
is important that the hands are slightly damp and exert constant
pressure on the sensors. Hands that are too dry or too wet may result
in abnormal readings.
11
11
11

MAINTENANCE

Safe and efficient use can only be achieved if the appliance is
properly installed and maintained. It is your responsibility to ensure
ADJUSTER
10