Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
CHAIR GANGING AND MAGAZINE HOLDER
Illustration 1
Nut
Illustration 2
Nut
Armed chair
Chair frame
Bolt
Ganging bracket
outer hole
Armless chair
Chair frame
Bolt
Ganging bracket
inner hole
Read all instructions and review illustrations
before installing.
Tools required for ganging:
Phillips screwdriver
/
" wrench
7
16
Ganging assembly includes:
(2) Ganging bracket
(4) Bolt
(4) Nut
Armed Chair Ganging (refer to Illustration 1):
1. Position two guest chairs next to each other.
2. On first chair, locate hole in chair frame just
below front edge of seat.
3. Position ganging bracket behind frame of first
chair as shown. Align outer hole in ganging
bracket with hole in chair frame.
4. Insert a bolt (from hardware pack) through hole
in chair frame and into outer hole on ganging
bracket. Thread a nut (from hardware pack)
onto bolt. Do not tighten nut at this time.
5. On second chair, position opposite end of gang-
ing bracket (attached to first chair) behind the
chair frame and align hole in chair frame with
the outer hole in ganging bracket.
6. Insert a bolt (from hardware pack) through hole
in chair frame and into outer hole on ganging
bracket. Thread a nut (from hardware pack)
onto bolt. Do not tighten nut at this time.
7. Repeat this procedure for rear of chairs.
8. Use the Phillips screwdriver and
fully tighten all nuts.
Armless Chair Ganging (refer to Illustration 2):
1. Position two guest chairs next to each other.
2. On first chair, locate hole in chair frame just
below front edge of seat.
3. Position ganging bracket behind frame of first
chair as shown. Align inner hole in ganging
bracket with hole in chair frame.
4. Insert a bolt (from hardware pack) through hole
in chair frame and into inner hole on ganging
bracket. Thread a nut (from hardware pack)
onto bolt. Do not tighten nut at this time.
5. On second chair, position opposite end of gang-
ing bracket (attached to first chair) behind the
chair frame and align hole in chair frame with
the inner hole in ganging bracket.
7
/
" wrench to
16
42-9830
(3/04)
Publicité
Manuels Connexes pour HON 4069
Sommaire des Matières pour HON 4069
- Page 1 CHAIR GANGING AND MAGAZINE HOLDER Illustration 1 Read all instructions and review illustrations before installing. Armed chair Tools required for ganging: Phillips screwdriver " wrench Ganging assembly includes: (2) Ganging bracket (4) Bolt (4) Nut Armed Chair Ganging (refer to Illustration 1): 1.
- Page 2 CHAIR GANGING AND MAGAZINE HOLDER Illustration 3 6. Insert a bolt (from hardware pack) through hole in chair Ganged frame and into inner hole on ganging bracket. Thread a chairs nut (from hardware pack) onto bolt. Do not tighten nut at this time.
- Page 3 ACOPLAMIENTO DE SILLAS Y REVISTERO Ilustración 1 Lea todas las instrucciones y examine las ilus- traciones antes de instalar. Silla con Herramientas requeridas para el acoplamiento: apoyabrazos Destornillador Phillips Llave de tuercas de 7/16 pulg El conjunto de acoplamiento incluye: (2) Escuadras de acoplamiento (4) Pernos (4) Tuercas...
- Page 4 ACOPLAMIENTO DE SILLAS Y REVISTERO Ilustración 3 4. Pase un perno (del paquete de tornillería) a través del Sillas agujero en el marco de la silla e insértelo en el agujero acopladas interior de la escuadra de acoplamiento. Enrosque una tuerca (del paquete de tornillería) en el perno.
-
Page 5: Montage Côte À Côte De Chaises Et Porte-Revues
MONTAGE CÔTE À CÔTE DE CHAISES ET PORTE-REVUES Illustration 1 Lire toutes les instructions et étudier les illu- strations avant l'installation. Chaise avec Outils requis pour le montage côte à côte : accoudoirs Tournevis cruciforme Clé de 7/16 po L'ensemble de montage côte à côte comprend : (2) Support de montage côte à... - Page 6 MONTAGE CÔTE À CÔTE DE CHAISES ET PORTE-REVUES Illustration 3 3. Placer le support de montage côte à côte derrière le Chaises bâti de la première chaise comme illustré. Aligner le montées trou intérieur du support de montage côte à côte avec côte à...