Lubrication - Ingersoll Rand TD Serie Manuel D'exploitation Et D'entretien

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

WARNING: Incorrect combinations of grinding wheel, wheel guard and tool speed could result in injury.
Correct combinations are specified below:
Guard Part Number
LE2–931

LUBRICATION

Ingersoll–Rand No. 10
Ingersoll–Rand No. 50
Always use an air line lubricator with these tools.
We recommend the following Filter–Lubricator–Regulator
Unit:
For USA – No. C28–04–FKG0–28
After each two hours of operation, if an air line lubricator is
not used, inject 1/2 to 1 cc of Ingersoll–Rand No. 10 Oil into
the Air Inlet.
Do not mark any nonmetallic surface of this tool with
customer identification codes. Such action could affect tool
performance.
MAIN LINES 3 TIMES
AIR TOOL INLET SIZE
TO
AIR
SYSTEM
TO
AIR
TOOL
LUBRICATOR
FILTER
REGULATOR
BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE
DRAIN REGULARLY
All manuals and user guides at all-guides.com
GRINDER SPECIFIC WARNINGS
Wheel Type
Wheel Diameter
in. (mm)
1
PLACING TOOL IN SERVICE
Ingersoll–Rand No. 68
COMPRESSOR
(Dwg. TPD905–1)
Maximum Wheel
Thickness
in. (mm)
3 (76)
1/2 (12.7)
MOUNTING THE ROUTER
ATTACHMENT
To mount a TD–RK4 or TD–RK6 Router Attachment to a
TD200 or TD250 Grinder having a collet, proceed as follows:
1. Use the Collet Body Wrench to hold the Collet Body
from turning and using the Collet Nut Wrench , unscrew
and remove the Collet Nut Assembly from the Grinder.
Remove the Collet .
2. Grasp the tool in copper–covered or leather–covered vise
jaws with the spindle upward and using a 1–1/2" wrench,
unscrew and remove the Clamp Nut . This is a left–hand
thread, rotate the Nut clockwise to remove it.
3. Remove the Clamp Spacer and install the Router
Attachment Clamp Spacer .
4. Thread the Clamp Nut onto the Housing and tighten the
Nut between 20 and 25 ft–lb (27 and 34 Nm) torque. This
is a left–hand thread, rotate the Nut counterclockwise
to tighten it.
5. Insert the Collet into the Collet Body and loosely thread
the Collet Nut onto the Collet Body. Insert a router bit
into the Collet and tighten the Collet Nut.
6. Install the Nosepiece Adapter over the bit and collet
assembly and thread it onto the Clamp Spacer. Tighten
the Adapter between 2 and 3 ft–lb (2.7 and 4.0 Nm)
torque. This is a left–hand thread, rotate the Adapter
counterclockwise to tighten it.
7. Install the Adapter Lock Screw in the Adapter and
tighten it between 12 and 18 in–lb (1.3 and 2.0 Nm)
torque.
8. Thread the Lock Nut onto the Nosepiece Adapter.
9. Thread the Nosepiece Assembly onto the Adapter and
then back the Lock Nut against the Assembly. Tighten the
Lock Nut between 14 and 19 ft–lb (19.0 and 25.8 Nm)
torque.
10. If a Trimmer Guide is used, thread the Guide into the
Nosepiece Assembly and tighten the Guide between 3
and 4 ft–lb (4.1 and 5.4 Nm) torque.
3
Maximum Speed
rpm
20 500
REV.000

Publicité

Table des Matières
loading

Table des Matières