Télécharger Imprimer la page

Publicité

Liens rapides

Assembly Instructions
Instructions pour l'assemblage
SAFETY WARNING
!
1.
Follow the information on the warnings appearing on the upper bunk end structure and on
the carton. Do not remove warning label from bed.
2.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
3.
Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
4.
Do not allow children under 6 years of age to use the upper bunk.
5.
Periodically check and ensure that the guardrail, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
6.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
7.
Prohibit more than one person on upper bunk.
8.
Always use the ladder for entering and leaving the upper bunk.
9.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10.
Use of a night light may provide added safety precaution for a child using the upper bunk.
11.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
12.
The use of water or sleep flotation mattresses is prohibited.
13.
STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
14.
Keep these instructions for future reference.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress, which is 37 1/2" - 38 1/2" width and 74"-75" long on upper bunk (twin size.)
Ensure that the thickness of the mattress does not exceed 6" and that the mattress surface is at
least 5" (127mm) below upper edge of guardrails.
WARNING:
Adult Assembly Required. This package contains small parts. Keep away from children.
Replacement Parts:
Replacement parts, including additional guardrails may be obtained from any
Night & Day Furniture Dealer.
Certified:
This bunk bed conforms to all applicable consumer product safety standards
16 CFR PARTS 1213, 1500, 1513 and ASTM F-1427
Page 1 de 9
Page 1 of 9
Ginger Twin Loft Bunk Bed
Lits superposés jumeaux loft, «Ginger»
TM
Note about Warning Labeling
The warning label on your bunk bed headboard is
there by law, and by law is not to be removed. The
adhesive used is difficult to peel off, will tear the paper
leaving a residue that is difficult to clean. We
recommend that you leave it where it is.
N&D 0119 F
US Patent #D623432

Publicité

loading

Sommaire des Matières pour Night & Day Furniture Ginger D623432

  • Page 1 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F SAFETY WARNING US Patent #D623432 Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.
  • Page 2: Avertissement De Sécurité

    Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F AVERTISSEMENT DE SÉCURITÉ Brevet américain #D623432 Suivre la mise en garde aparaissant sur la structure du lit du haut et sur le carton. Ne pas enlever l’avertissement apparaissant sur le lit.
  • Page 3 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F Parts in Box 1 Pièces dans la boite 2 Pièces dans la boite 3 Parts in Box 2 Parts in Box 3 Pièces dans la boite 1 Post 4 Post 3...
  • Page 4 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F Parts in Box 1 / Hardware in this Box Pièces dans la boite 1 Quincaillerie incluse Échelle 1: 1 Scale 1: 1 100mm Bolts Vis (100mm) x 21 Wood Screws...
  • Page 5 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F Assemble the Rear parts: Rear Guard Rail, Stretcher, Long Frame to Posts 4 & 3 Assembler les parties arrière: rail de sécurité, rail d'étirement, et le long châssis à l'emplacement 4 & 3 Identify the Posts 4 &...
  • Page 6 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F Assemble the Left and Right side frames Assembler les côtés gauche et droit du châssis Identify the Posts 2 & 1, as shown below and lay them out on the floor, with the end frames.
  • Page 7 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0421 F Bolt Join the end frames to the Rear posts (80mm) Joindre les pieds de lit aux poteaux arrière Attach the assembled left hand side to the assembled rear posts using 80mm Bolts and Barrel Nuts.
  • Page 8 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F Attach the front stretcher Attach the Front Guard Rail and the Center Rail Attacher le rail d'étirement du devant Attacher le rail de sécurité du devant et le rail du centre Tap Wooden Dowels into the end of the Front Guard Rail.
  • Page 9 Ginger Twin Loft Bunk Bed Assembly Instructions Lits superposés jumeaux loft, «Ginger» Instructions pour l’assemblage N&D 0119 F Visser les lattes aux rails d'étirement Attach the Ladder to the Front Stretcher Bolt the Slats to the Stretchers Attacher l'échelle au rail d'étirement du devant Lay the Slats inside the Stretchers as shown below, and Bolt in place with the 30mm Threaded Wood Bolts (total 16 Bolts) and 30mm Wood Screws (total 16 Screws).