Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
_
If the motor runs smoothly, slowly push
the choke again.
Regulating the speed (fig. A)
_
Keep the lock-off button (2) depressed.
_
Press the accelerator (1) to increase the
speed. The further you press the accelerator,
the higher the speed of the machine.
Switching off (fig. A)
_
Slide the stop switch (4) to the downward
position.
CLEANING AND MAINTENANCE
The machine does not require any special
maintenance.
_
Regularly clean the ventilation slots.
Cleaning the machine (fig. A)
The machine must be cleaned after each use.
_
Remove the bar (10) from the machine.
_
Remove the chain (11) from the bar.
_
Clean the machine using a soft cloth.
_
Clean the bar using a soft cloth.
_
Clean the chain using a soft brush.
_
Apply a thin layer of oil to the bar to avoid
oxidation.
_
Place the protective cover over the bar.
Checking the oil level (fig. F)
The oil level must be checked before each
use and after each 10 minutes of use.
_
Place the machine on its side on a stable
underground.
_
Remove the plug (12) from the filling point.
_
Use a clean stick to determine the level.
_
If the level is below 2/3 of the part used
for measurement, refill the oil.
_
Replace the plug.
Checking the fuel level (fig. F)
The fuel level must be checked before each use.
_
Place the machine on its side on a stable
underground.
_
Remove the plug (13) from the filling point.
_
Use a clean stick to determine the level.
_
If the level is below 2/3 of the part used
for measurement, refill the fuel.
_
Replace the plug.
Cleaning the air filter (fig. G)
The air filter must be cleaned every 50 operating
hours.
_
Loosen the knob (21) and remove the cover (22).
_
Remove the filter (23).
_
Clean the filter with spirits or ethanol.
_
Dry the filter with a soft cloth.
_
Replace the filter.
_
Replace the cover and tighten the knob.
Before performing
maintenance to the
machine, always switch
off the machine.
Checking the spark plug (fig. G & H)
_
Loosen the knob (21) and remove the cover (22).
_
Remove the filter (23).
_
Remove the spark plug cable (24) from the spark
plug (25).
_
Remove the spark plug using the spark plug
spanner.
_
Clean the electrode (26) using a steel brush.
_
Check the contact distance (correct value
0.7 - 0.8 mm) and adjust as necessary.
_
Replace the spark plug.
Sharpening the chain
The chain should preferably be sharpened
by a recognised technician.
_
Take the machine to your dealer to have
the chain sharpened.
TECHNICAL DATA
TRT3841CW
Power input W
CC
Hp
No-load speed min-1
Bar length mm
Chain brake time ms
Oil container capacity ml
Fuel container capacity ml
Fuel consumption kg/h
Oil
Fuel unleaded gasoline with 2-cycle oil (25:1)
Weight kg
Level of sound pressure:
LpA (sound pressure) dB(A)
LWA (acoustic power) dB(A)
Weighted root mean square acceleration
value:
TRT4345CW
Power input W
CC
Hp
No-load speed min-1
Bar length mm
Chain brake time ms
Oil container capacity ml
Fuel container capacity ml
Fuel consumption kg/h
Oil
Fuel unleaded gasoline with 2-cycle oil (25:1)
Weight kg
Level of sound pressure:
LpA (sound pressure) dB(A)
LWA (acoustic power) dB(A)
Weighted root mean square acceleration
value:
1.400
37.20
1.9
3000
400
83.1
210
310
0.9
SAE 10W-30
6.5
94
114
8.33 m/s²
1.800
45
2.4
3.000
440
68.5
260
550
0.9
SAE 10W-30
7.5
103
114
5.55 m/s²
Publicité
Table des Matières
