NOMA 52-4075 Instructions D'installation Et D'utilisation
NOMA 52-4075 Instructions D'installation Et D'utilisation

NOMA 52-4075 Instructions D'installation Et D'utilisation

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Security Light with
Motion-activated Sensor
This product is ENERGY STAR
when used with 120 Watt bulbs.
Models 52-4075 / 52-4076
Installation and Operating
Instructions
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
This package includes:
Lamp Holders
Cover
Plate
Sensor
Light Control
Requirements
• The Light Control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a qualified elec-
trician. Please check the codes in your area.
• This product is intended for use with a junction box
marked for use in wet locations.
• The backplate has knockouts so the sensor can be
mounted on most junction boxes.
• In some applications a universal adaptor plate may
be needed. Adaptors are available at home centers
and electrical supply stores.
All manuals and user guides at all-guides.com
compliant
®
4 Mounting
Screws (2 sizes)
Gasket
2 Wire
Connectors
OPERATION
Mode:
On-Time:
Test
5 Sec
Normal
1, 5, 10 min.
Manual
Until Dawn*
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1
the circuitry to calibrate.
TEST
Put the ON-TIME switch on the bottom
of the sensor in the TEST position.
AUTO
Put the ON-TIME switch in the 1, 5,
or 10 minute position.
MANUAL MODE
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Mode Switching Summary
TEST
AUTO
MANUAL MODE
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
Works:
Day
Night
x
x
x
x
/
minutes for
1
2
ON-TIME
10 5 1 TEST
ON-TIME
10 5 1 TEST
1 Second OFF
then...
... back on.
Move ON-TIME Switch to
1, 5, or 10 minutes
Flip light switch off
for one second then
back on*
598-1284-00

Publicité

Table des Matières
loading

Sommaire des Matières pour NOMA 52-4075

  • Page 1 120 Watt bulbs. the circuitry to calibrate. TEST ON-TIME Put the ON-TIME switch on the bottom Models 52-4075 / 52-4076 of the sensor in the TEST position. 10 5 1 TEST Installation and Operating AUTO Instructions...
  • Page 2 All manuals and user guides at all-guides.com INSTALLATION ire the ight ontroL ❒ Turn power off at the fuse or circuit breaker. For easy installation, select an existing light operated ❒ Remove the existing light fixture. by a wall switch for replacement. ❒...
  • Page 3 All manuals and user guides at all-guides.com TEST AND ADJUSTMENT ❒ Loosen the clamp screw in the Clamp sensor ball joint and gently Screw rotate the sensor. ❒ Turn on the circuit breaker and light switch. ❒ Walk through the coverage Ball NOTE: Sensor has a 1 minute warm up period...
  • Page 4 All manuals and user guides at all-guides.com TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE SYMPTOM POSSIBLE CAUSE Lights will not come 1. Light switch is turned off. Lights stay on 1. A flood lamp is positioned too close to continuously. 2. F l o o d l i g h t i s l o o s e o r the sensor or pointed at nearby objects burned out.
  • Page 5: Fonctionnement

    120 watts. * Revient au mode automatique au lever du soleil. Note: Après mise en circuit, attendre enfiron minute pour que l’étalonnage du circuit soit Modèles 52-4075 / 52-4076 complété. Instructions d'installation ESSAI et mode d'emploi ON-TIME Amener en position d’essai (TEST)
  • Page 6: Montage Mural

    All manuals and user guides at all-guides.com INSTALLATION CÂBLAGE DE LA COMMANDE D’ÉCLAIRAGE Pour faciliter l’installation, choisir un appareil d’éclairage devant être remplacé et qui est déjà commandé par ❒ Couper l’alimentation du circuit d’éclairage au un interrupteur. fusible ou au disjoncteur. Pour assurer un rendement maximal, monter ❒...
  • Page 7: Essais Et Réglages

    All manuals and user guides at all-guides.com ESSAIS ET RÉGLAGES ❒ Desserrer la vis de blocage Vis de de la rotule et faire pivoter le blocage ❒ Mettre en circuit le disjoncteur et l’interrupteur détecteur pour pointer. d’éclairage. Rotule ❒ Marcher dans la zone de NOTE: Le capteur doit se réchauffer 1 minute avant couverture et noter à...
  • Page 8: Dépannage

    All manuals and user guides at all-guides.com DÉPANNAGE SYMPTÔME CAUSE POSSIBLE SYMPTÔME CAUSE POSSIBLE L’éclairage ne s’al- 1. L’interrupteur d’éclairage est hors L’éclairage reste 1. Un projecteur est situé trop près du lume pas. allumé continuel- tension. détecteur ou pointé vers des objets lement.

Ce manuel est également adapté pour:

52-4076

Table des Matières