Operation; Cleaning And Maintenance; Troubleshooting - Giostyle GS3+ 12V 30/26L Mode D'emploi

a long time even when the coolbox is switched off. To maximize
and extend the cooling effect over time, we suggest you use the
original Gio'Style ice packs (see ACCESSORIES).
Caution!
The appliance is suitable to keep cool food and drinks in
their original containers. Never use the coolbox for more
than 72 hours of continuous operation.
Prolonged and continuous use may reduce performance or even
damage the cooling system. Once the coolbox is switched off, wait
at least 2 hours before turning it on again.
Caution!
After a long period of operation, water may form and ac-
cumulate at the bottom of the coolbox. This is normal, as
air humidity condenses during the cooling process. This does not
mean the coolbox is faulty.
If necessary, remove excess humidity with a dry cloth.
N.B.!
The cooling is produced by a Peltier cooling system
that does not contain CFCs or coolants.

5. OPERATION

• Once connected to the power source the coolbox immediately
begins to operate. It can cool food and keep it cold.
• To turn off the coolbox just disconnect the power cord.
Note for dual-power models (Energy Saver), with function key:
when connected to your home 230 VAC electrical system, you can
select three types of operation:
1. ECO FUNCTION (green LED):
the appliance complies with the Energy Saving Directive (EC
Regulation No. 643/2009), maintaining the assigned energy
class (see section 1), ensuring an internal temperature of °C >
14.5 °C with an outside temperature of between 16 °C and 38 °C.
2. COOL FUNCTION (orange LED):
the appliance DOES NOT comply with the Energy Saving Direc-
tive (EC Regulation No. 643/2009) of reference and operates in
intermediate mode.

7. TROUBLESHOOTING

PROBLEM
The coolbox does not work and the cool-
ing fan does not turn (if connected to the
power socket) or led OFF (only for the
230 VAC version).
The coolbox does not work and the
cooling fan does not turn if connected
to the 230V household mains (for mod-
els equipped with built-in power feeder
only) or led OFF (only for the 230 VAC
version):
The fan turns but the coolbox does not cool.
Water forms inside the coolbox during
operation.
POSSIBLE CAUSE
The vehicle power socket does not receive voltage.
The cigarette lighter socket fuse is blown.
The vehicle fuse is blown.
The cooling fan is broken.
The socket does not work
The plug is not properly inserted
The cooling fan is broken.
The built-in power feeder is faulty.
The AC power cable is faulty.
Ventilation slots are partly or thoroughly obstructed.
The thermoelectric module (Peltier) is faulty.
The coolbox has been operating for a long time, which
causes the formation of condensate.
Autogoods "130"
3. PLUS FUNCTION (red LED):
the appliance DOES NOT comply with the Energy Saving Direc-
tive (EC Regulation No. 643/2009), but operates continuously
at maximum power and, therefore, the temperature may drop to
4.5 °C (always depending on the outside temperature).
To select the three settings press the function key for about 5 seconds.
ATTENTION: After 48 ±3 hours of continuous operation,
the coolbox will return to operating in ECO mode.
mode.
5 - B. BATTERY SAVER (WHERE PRESENT)
N.B.!
The model SHIVER 40 12V DC has a Battery Saver sys-
tem and display of the internal temperature.
1) No protection for the car battery (ATTENTION: this setting may
lead to the complete discharge of the car battery)
2) Maximum battery protection (10.6 V)
3) Medium battery protection (10 V)

6. CLEANING AND MAINTENANCE

Warning!
Before cleaning the coolbox, disconnect the power cable
from the mains socket or the car power socket.
Warning!
Never clean the appliance under running water.
• For cleaning purposes do not use corrosive or abrasive
detergents or rough objects, that may damage the appliance
(blades, spatulas, etc.).
• Clean the coolbox inside and outside from time to time with a wet
cloth.
• Protect the cooling lid from the penetration of liquids, sand or
dust.
ACTION
In many motor vehicles, switching on the dashboard is required to
operate the power socket.
ing printed on the fuse.
Replace the fuse according to the instructions provided by the vehicle
user's manual.
Contact our customer service (see § Guarantee).
Verify that the AC socket is working
Verify the correct insertion of the plug into the socket by pulling it out
and putting it back
Contact our customer service (see § Guarantee).
Contact our customer service (see § Guarantee).
Replace the cable with a new original one.
Check both internal and external ventilation slots. Move the coolbox
to a place where it can be more ventilated.
Contact our customer service (see § Guarantee).
Dry up excess water with a cloth, ensuring that the coolbox is discon-
nected. Wait a few hours before switching it on again.
-
7