NUTRIBULLET robot culinaire Manuel D'utilisation page 6

10
Remove your food from the
Work Bowl using a spatula
or spoon. Dispose of any
leftover food in the bowl,
then clean the bowl, blades,
and other parts to avoid food
OFF LOW HIGH PULSE
residue buildup.
Using the dual-size
food pusher.
The Dual-Size Food Pusher features a smaller
pusher inside a larger one. Use the Full-Sized
Pusher for guiding bigger pieces of food
down the Feed Chute — like when shredding
lettuce or a big block of cheese.
Unlock the Inner Pusher to create a more
narrow Feed Chute, and use the Inner Pusher
for better control with thinner ingredients,
such as zucchini or carrots. The narrow Feed
Chute is also ideal for drizzling
in liquids during processing.
Separate the Inner
Pusher from
the outer pusher piece
by gripping the circular
Pusher Cap. Twist
the top of the pusher
clockwise and lift the
Inner Pusher from the
outer piece.
Troubleshooting.
PROBLEM
Unit does not power on.
SOLUTIONS
Make sure the Power Cord is plugged into an
electrical outlet, and that outlet has power.
Make sure the Work Bowl Lid is locked into place on
top of the Work Bowl. The arrow on the lid and handle
should line up when properly locked in place. If the
lid becomes unlocked at any time while the motor is
running, the unit will stop running and the blue lights
around the buttons will flash.
Make sure the Work Bowl is locked into place on the
Motor Base. When placing the Work Bowl on the
Motor Base, turn the handle clockwise until you hear
a click – indicating that the bowl is properly locked in
place.
10
PROBLEM
The Food Processor stopped in the middle of
processing, and the control panel lights flashed three
times.
SOLUTIONS
You have exceed 10 minutes of continuous running
time. Unplug the Food Processor and keep the unit
off for 15 minutes before continuing use.
PROBLEM
Feed Chute is blocked.
SOLUTIONS
If you notice that a piece or cluster of food appears
to be stuck in the Feed Chute, blocking food flow,
turn the motor OFF. Unlock the Work Bowl Lid
from the Work Bowl, and use the Food Pusher, a
spatula, or spoon to remove the stuck food before
reassembling.
If the Work Bowl is nearly full of food, that may stop
the flow of food down the Feed Chute. If the food
has reached to just below the disc attachment, you'll
need to empty the bowl before processing more
food. Turn the motor OFF, wait until the blades have
come to a complete stop and disassemble the unit to
empty the Work Bowl.
Care & maintenance.
Cleaning the nutribullet ® Food Processor is quick and
easy. All detachable parts (Blade Adaptor, Chopping
Blade, Dough Blade, Slice/Shred Discs, Spiralizer
Disc, Work Bowl, Work Bowl Lid, and Dual-Size Food
Pusher) are TOP RACK dishwasher-safe. The Motor
Base can be quickly hand-washed with a damp cloth.
Read on for best practices.
STEP 1:
The most important thing — ALWAYS POWER OFF THE UNIT
and UNPLUG the Motor Base from the power outlet when it is
not in use.
NOTE:
Do not attempt to handle the appliance until all parts have
stopped moving! This includes during assembly and disassembly,
while changing accessories, during cleaning, and any time you leave
the machine unattended
STEP 2:
Detach the blades and other attachments from the Motor
Base.
STEP 3:
Clean the individual components as recommended in the
following sections.
MOTOR BASE:
NEVER
• To avoid risk of injury, attempt to clean the
actuator system on the Motor Base while the unit is
plugged in.
• Do not attempt to remove any pieces from the Motor
Base.
• Use a sponge or dish cloth dampened with warm soapy
water to wipe down the Motor Base until clean.
• If necessary, you may use a small brush to scrub the
actuator system area to ensure it's clean.
• To clean leakage residue from the Motor Base, wipe with
a damp sponge and warm water.
WARNING: Never submerge the Motor Base in water.
ALL DETACHABLE PARTS:
WARNING: Blades are sharp! Handle all blade
attachments with care when cleaning!
• The Blade Adaptor, Blade Attachments, Work Bowl,
Work Bowl Lid, and Dual-Size Food Pusher are all
TOP RACK dishwasher-safe. These parts may also be
cleaned by hand with warm soapy water.
• We recommend cleaning all removable parts after
each use to reduce the buildup of residue.
WARNING: NEVER use the sanitize cycle — heat this high
can warp the plastic.
WARNING: Do not clean the Work Bowl, Work Bowl Lid,
or other parts of the appliance with steel wool pads/
balls or other hard material that might scratch your Food
Processor.
How to store.
The blade attachments conveniently store within
the Work Bowl when not in use. Make sure the
unit is powered off and unplugged before placing
attachments in the Work Bowl for storage. Read on
for details:
NOTE: All included blades and discs will not store in the work
bowl together, you will have two storage options:
OPTION 1: Chopping Blade, Dough Blade, 2 Slice/Shred Discs
OPTION 2: Chopping Blade, Dough Blade, 1 Slice/Shred Disc,
Spiralizer Disc
STEP 1:
Place the Blade Adaptor on the center shaft.
STEP 2:
Lower the Chopping Blade onto the Lower the
Chopping Blade onto the blade shaft, and then lower
the Dough Blade onto the blade shaft so that it sits
above the Chopping Blade on the shaft.
STEP 3:
Lower the disc attachments onto the adaptor, on top of
the Chopping Blade. In storage mode, the discs should
sit in the lower position on the adaptor than when used
in normal operation. In storage mode, the lines on the
disc will NOT be aligned with the lines on the adaptor.
STEP 4:
The Spiralizer Disc should be the last disc stored, if
storing with one of the Slice/Shred Discs. When storing
the Spiralizer Disc, align the
notches on the Spiralizer
Disc with the tabs that are
located inside of the Motor
Base towards the top. Ensure
the disc is properly seated on
the blade and adapter, inside
of the Motor Base, and turn
the Spiralizer Disc so that the
'FRONT' is aligned with the
front of the Motor Base.
STEP 5:
Place the Work Bowl Lid onto the Work Bowl and lock
into place, with the Dual-Size Pusher nestled in the
Feed Chute.
NOTE: The power cord wraps under the bottom of the Motor
Base – keeping it neatly tucked away when stored.
Accessories.
To order accessories, please visit our website at
nutribullet.nu or nutriliving.shop.
Waranty registration.
Please visit nutriliving.shop to register your new
nutribullet ® Smart Touch Blender™ Combo. You
will be asked to enter the Serial Number* of your
product, along with the purchase date and name of
the shop of purchase. The registration will enable
us to contact you in the unlikely event of a product
safety notification. By registering your product you
acknowledge to have read and understood the
instructions for safety and use, and the warnings set
forth in the accompanying instructions.
*To find the serial number, check under the
Motor Base.
12345678910110
How to find the serial
number under the
engine base.
Are you happy with your
nutribullet ?
®
Share your recipes, posts, tips & tricks! Like & follow us
@nutribullet.nordics
Tag your blends #nutribullet #nutribullet.nordics
#nutrilovers #healthy #healthylifestyle
11