NUTRIBULLET robot culinaire Manuel D'utilisation page 4

Control panel.
The nutribullet Food Processor features a multi-
®
speed control panel for all types of food prep.
OFF LOW HIGH PULSE
OFF:
Stops the Food Processor when operating on
continuous LOW or HIGH speeds.
OFF LOW HIGH PULSE
LOW:
Continuous LOW-speed chopping or mixing.
OFF LOW HIGH PULSE
HIGH:
Continuous HIGH-speed chopping or mixing.
OFF LOW HIGH PULSE
PULSE:
A burst of chopping or mixing that runs at HIGH
speed. PULSE must be held to activate; motion will
stop when the button is released.
6
Assembly & use.
Before first use.
Before using your nutribullet ® Food
Processor for the first time, please take a
moment to perform the steps below.
1. UNPACK
Open box. Remove the Motor Base and all
attachments. Place all parts on a flat, dry
surface.
2. CLEAN
Rinse all detachable parts and accessories. All
Motor Base
parts except the are dishwasher
safe, or can be cleaned by rinsing with warm,
Motor Base
soapy water. Clean the with a
clean, damp cloth.
WARNING: Never submerge the Motor Base in wa-
ter or any other liquid. See Care
& Maintenance instructions on page 22 for more
detailed cleaning instructions.
Assembly.
Review all warning and caution statements in the
Important Safeguards section (pages 2-5) and
above before proceeding to Step 1.
1
Place the Work Bowl on a
clean, dry, flat surface, like a
countertop or table.
2
Blade Adaptor
Place the
Work Bowl.
the Lower the
Blade Adaptor
onto the top
of the shaft located in the
center of the Work Bowl.
Push down so the adaptor is
firmly and securely in place.
3a
If using the Chopping Blade
or Dough Blade: Hold the
plastic center of the blade,
and carefully place it on
top of the Blade Adaptor.
Slide the blade down until
it reaches the bottom of the
Work Bowl.
Press it down
firmly to set it in place.
3b
If using a Slice/Shred disc
attachment:
attachments can be placed
in 2 different positions on the
Blade Adaptor.
position is for storage, and
the higher position is for use.
Hold the center knob of the
disc, and carefully place it on
the
markings on the disc
with the markings on the
Blade Adaptor,
lines connect. If the disc
appears to be in the lower
position, remove the disc and
rotate until the markings line
up and the disc sits in the
higher position.
CAUTION: Blades are sharp!
Handle carefully. Keep fingers
away from the blade's sharp
edges. Always hold blades by
grasping the plastic areas.
4
If using the Spiralizer disc
attachment:
notches on the
Disc
located inside the
towards the top. Once the
disc is properly seated on the
Blade Adaptor
of the
Spiralizer Disc
'FRONT'
front of the
spiralizer part of the disc will
sit directly under the
Chute.
CAUTION: Never run the motor
with more than 1 blade attached.
in
Using the chopping blade.
The Chopping Blade is a versatile blade that can be
used to chop, mix, mince, or purée foods.
1
Place the
with the
attached, on a clean,
dry, flat surface like a
countertop. Refer to the
assembly instructions
on page 12 for how to
properly attach the
Chopping Blade.
The disc
The lower
Blade Adaptor. Align the
so that the
Align the
Spiralizer
with the tabs that are
Work Bowl
and inside
Work Bowl, turn the
so that the
is aligned with the
Motor Base. The
Feed
OFF LOW HIGH PULSE
Work Bowl,
Chopping Blade
OFF LOW HIGH PULSE
2
Prepare food (cut into
smaller pieces, remove
seeds, etc.) and place into
the Work Bowl. Do not
overload bowl with food.
If you are using liquid
ingredients do not fill past
the LIQUID MAX line.
NOTE: Make sure the Chopping
Blade has been attached to the
Work Bowl BEFORE adding
food to the bowl.
3
Place the Work Bowl Lid
on top of the Work Bowl.
Turn the lid clockwise, lining
up the arrows on the lid and
handle, to lock into place.
Place the Dual-Size Food
Pusher into the Feed Chute.
NOTE: The motor will not run
unless the lid is locked into place.
4
Place the Work Bowl, with
lid attached, onto the
Motor Base. Turn the bowl
clockwise to lock into place.
You should hear a click when
the bowl is properly locked
into place.
5a
Plug in the unit, then press
your desired speed to
start processing food. The
blue light will illuminate over
the speed that is currently
running.
5b
If you need to add liquid
while processing, unlock
the Inner Pusher by
turning the Pusher Cap
clockwise. Once unlocked, lift
the Inner Pusher and drizzle
liquid through the narrow
chute.
NOTE: Do not fill liquid
ingredients past the LIQUID
MAX line.
7