Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Tie down bracket
Hitch Shown In Proper Position
Equipment Required: Small Flat Head Screwdriver, Lubricant
or Soapy water
Fastener Kit: 24828F
Wrenches: 12mm, 13mm, 9/16", 11/16", & 3/4" (2)
Remove
existing M8
bolts from end
of each frame
rail.
1
Qty. (2)
Hex bolt M8 X 1.25 X 35 CL9.8
2
Qty. (2)
Hex bolt 1/2-13 X 2.00 GR5
3
Qty. (4)
Spacer
4
Qty. (2)
Conical washer 1/2"
1.
Remove appearance panel which covers the trunk pan. Remove the (7) plastic rivets that fasten the fascia tabs to the vehicle.
Note: Remove the center of the rivet with a screwdriver. Return appearance panel and fasteners to vehicle owner.
2.
Remove existing M8 bolts (2) from end of each frame rail. Return fasteners to owner. See Figure 2.
3.
Lower exhaust system at the rubber isolator. Note: Spraying a lubricant or soapy water on the metal hanger rod and the rubber
isolator helps removal.
4.
Raise hitch into position over the exhaust.
5.
Install fasteners as shown above. See Figure 1.
6.
Tighten all fasteners to called-out torque specification
7.
Raise exhaust system back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008 Cequent Towing Products
Installation Instructions
Fascia
Drawbar Kit:
3593
Drawbar must be used in
the Rise position only.
Note: Fasteners typical both sides
Existing
weldnut
Figure 2.
Tighten all M8 CL9.8 fasteners with torque wrench to 17 Lb.-Ft. (23 N*M)
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Scion xD
Do Not Exceed Lower of Towing Vehicle
Wiring Access Location:
3 7
Tie down
bracket
1
6 7
2
5
Qty. (2)
6
Qty. (2)
7
Qty. (4)
8
Qty. (2)
Sheet 1 of 3
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
8
5
3 4
Figure 1.
Hex nut 1/2-13
Hex bolt 3/8-16 X 1.75 GR5
Conical washer 3/8"
Hex nut 3/8-16
24828N
10-17-08
Part Numbers:
24828
60214
77200
Exhaust not
shown for
clarity
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 24828
Sommaire des Matières pour Cequent Towing Products 24828
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24828N 10-17-08 Rev. A 2008 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24828N 10-17-08 Rev. A 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2008 Cequent Towing Products Hoja 3 de 3 24828N 10-17-08 Rev.