Cequent Performance Products 36522 Instructions D'installation

Vehicle
Frame end
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36522F
Wrenches: 13mm, 9/16", 3/4", 7/8"
Drill bits: 1/2", to enlarge hole,
on Lacrosse only.
Suspension
Loosen outside 8mm
mount.
tailpipe hanger bolt
both sides vehicle
(not shown), for ease
.
of installation
1 8
Use (2) spacer
washers per side,
between hitch and
.
vehicle attachment
Remove existing inner tailpipe
hanger 8mm bolts, and replace with hanger 8mm bolts, and replace with
supplied 8mm bolts.
Figure 1.
1 1 1 1
Qty. (2) M8-1.25 x 40mm CL. 10.9 Bolt
2 2 2 2
Qty. (4) 3/8" Flat Washers
3 3 3 3
Qty. (2) Hex Bolt, 1/2"-13 X 2-1/4" Gr.5
4 4 4 4
Qty. (3) Conical Toothed Washer, 1/2"
5 5 5 5
Qty. (1) Hex Nut, 1/2"-13 Gr. 2
6 6 6 6
Qty. (1) Hex Bolt, 1/2"-13 X 1-1/2" Gr.5
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water
and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection.
Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
z
2013 Cequent Performance Products , Inc.
Installation Instructions
Bumper
Fascia
All models including CX, CXL-FWD, CXL-AWD & CXS
Drawbar Kit:
36061
Drawbar must be used in the
Rise position only.
Bolt-on bracket for
LaCrosse CXL &
CXS models.`
9
5
7
4
4
3
2
Hitch
forward
bracket
1 8
Bolt-on bracket for
Regal , LaCrosse CX
Buick Lacrosse
Buick Regal
All models except GS model
Chevrolet Malibu
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Carrying
Ball Mount
Wiring Access Location:
Lacrosse PC3, 4
Regal
Malibu
Slide handle nut through
opening in bottom of
4
suspension mount.
3
*
2
8mm bolt to replace (step 1).
& Malibu models.
Slide handle nut
through opening in
bottom of suspension
7 7 7 7
Qty. (2) Hex nut M8 x 1.25
8 8 8 8
Qty. (2) Conical Toothed Washer, 3/8"
9 9 9 9
Qty. (1) Handle-Nut, ½"
Qty. (3) Spacer, wedge
11 Qty. (2) Flat washer ½"
Sheet 1 of 4 36522N
Part Numbers:
Max Gross
Trailer WT (LB)
3500 (1589 Kg)
Accessory Rating
PC1, 2
PC3, 4
8
1
Vehicle
forward
Suspension
mount.
11
9
4
6
Hitch forward bracket
mount.
4
3
(*torque spec below)
4-18-13
Form: F205 Rev A 5-6-05
36522
90226
06153
Max Tongue
WT (LB)
300 (136 Kg)
B
Existing
weldnut
7
Figure 2.
*
Rev. A