Setting Up The Machine For Brewing A Travel Tumbler/Mug Of Coffee; Brew Strength Selection - brim SW20 Manuel D'instructions

7. Plug the power cord into 120V/60HZ power supply socket, the background indicator will be
illuminated; "AM 12:00" will flash. Set the clock time using the HOUR & MIN buttons, press SELECT, it
will beep to confirm the time. The back-lit indicator will go into sleep mode within 15 seconds and will
release a beep if no further buttons are selected.
8. Press the "my cup" button, the indicator light in "my cup" will turn on and the coffee maker will begin
the brew cycle.
NOTE: Do not remove the cup during the brewing cycle. To interrupt the brew process at any time,
press the "my cup" button, the coffee maker will beep, the indicator light in "my cup" will turn off, and
the brewing and the dripping process will stop immediately. The current clock will appear on the LCD.
If the brew cycle is interrupted the coffee that brewed into the brew basket will remain in the brew
basket. Wait for the coffee to cool before emptying the accumulated coffee.
9. The coffee maker will beep once and the indicator light in "my cup" will turn off when the coffee is
finished brewing and dripping, wait until the dripping coffee has stopped before removing your cup.
Be careful to remove slowly as it contains hot liquid.
NOTE: The heating plate is inactive during the brewing cycle when brewing "my cup".
Setting up the machine for brewing a travel coffee tumbler/mug
IMPORTANT: Before brewing a tumbler of coffee, please assure there is no
residual water inside the water tank from the last brew, this will affect the final
volume of the output coffee. Also, filter must be clean.
1. Remove carafe and press on the tray release button, located on the right
hand side of the machine to release the tray
2. Manually remove the drip tray cover from the tray assembly using front tab.
Fold the tray back to the vertical position and assure it is locked in place.
3. Place the drip tray cover over the heating plate with tab facing forward.
4. Lift to open the coffee maker lid. Fill the travel tumbler you want to brew
with cold tap water, and pour into water reservoir at the back of the unit.
The translucent water level indicator can be easily viewed at the right side
of the unit.
5. Place the travel tumbler on drip tray cover.
6. Place the permanent filter in the removable filter holder. Fill up with ground coffee to the markings
inside the permanent filter for a perfect tumbler of coffee. You may adjust the flavor by adding more or
less ground coffee.
7. Close the lid.
8. Plug the power cord into 120V/60HZ power supply socket, the background indicator will be
illuminated; "AM 12:00" will flash. Set the clock time using the HOUR & MIN buttons, press SELECT, it
will beep to confirm the time. The back-lit indicator will go into sleep mode within 15 seconds and will
release a beep if no further buttons are selected.
9. Press the "my cup" button, the indicator light in "my cup" button will turn on and the coffee maker will
begin the brew cycle.
NOTE: Do not remove the cup during the brewing cycle. To interrupt the brew process at any time,
press "my cup" button, the coffee maker will beep, the indicator light in "my cup" will turn off, and
the brewing and the dripping process will stop immediately. The current clock will appear on the LCD.
If the brew cycle is interrupted the coffee that brewed into the brew basket will remain in the brew
basket. Wait for the coffee to cool before emptying the accumulated coffee.
10. The coffee maker will beep once and the indicator light in "my cup" will turn off when the coffee
is finished brewing and dripping, wait until the coffee has stopped dripping. The travel tumbler can
then be removed from the coffee maker. Be careful to remove slowly as it contains hot liquid.
NOTE: The heating plate is inactive during the brewing cycle when brewing "my cup".
Brew strength selection: Regular or Bold
The Bold setting adjusts the brewing cycle, allowing more time for the coffee to "steep" to extract further
oils and flavor from the ground coffee bean. This results in a bolder tasting pot of coffee.
NOTE: The BOLD strength selection is available only when brewing a 12-cup carafe, when brewing a cup of
coffee or a travel tumbler coffee, only the regular strength of coffee can be brewed.
1. By default, the coffee maker is set to brew a carafe of coffee at regular strength.
2. If a BOLD flavor of coffee is desired, press MODE button once, the BOLD icon will flash, and then
press SELECT. BOLD icon stays on the LCD screen.
3. To deactivate the BOLD strength mode, simply press MODE button once, the BOLD icon will flash
on the LCD screen, press SELECT button to remove the BOLD strength mode. The BOLD icon will
disappear from the LCD screen.
13