Adler europe AD 2818 Mode D'emploi page 4

19. Do not leave switched on equipment or adapter without supervision.
20. Never use this device close to water, e.g.: Under shower, in bathtube, or above
sink filled with water.
21. If the device utilises a power adaptor, do not cover it, because this can cause a
dangerous temperature rise and can damage the device. Always connect the power
adaptor cable to the device, and then connect the power adaptor to the power socket.
22. The cutting scissors are very sharp. Use caution when assembling, dismantling and
cleaning. Do not touch any elements of the moving blade during the operation!
23.Do not use the device for more than 10 minutes at a time. After 10 minutes have
elapsed, turn it off for approximately 5 minutes. DO NOT CHARGE THE BATTERY FOR
LONGER THAN 48 HOURS – this can cause irreversible damage to the battery.
24.The charging process should be conducted in temperatures between 5-35 degrees
Celsius.
25.Do not wash the blades in water.
26.Only change comb attachments when the device is switched off.
27. Use only original accessories.
28. To remove hair from inside the machine, use only the included brush.
29. Do not use the device in the bath.
30. Do not use the device on people who are sleeping.
31. During operation, do not place the device on wet surfaces or clothes.
32. The device is not designed to work with external schedulers or separate remote control
system.
33. Do not insert the trimmer into the nose or ear to a depth greater than 5 mm as this may
cause damage to the nasal mucous membrane or eardrum.
DESCRIPTION OF THE DEVICE
1. Indicator light
4. Thinning out adjuster
7. Blades
CHARGING BATTERIES
Charging is required before you can use the device. To start charging the batteries, connect the power cord to a power socket (230V ~
50Hz). Then insert the plug of the power cord into the plug receptacle of the clipper. The "charge" indicator light will start to glow. It will be
glowing until the device has been disconnected from the mains. Charging should take about 8 hours. A fully charged battery is enough to
provide 45 minutes of continuous operation. When the batteries are fully charged, remove the charger from the power socket. When the
hair clipper is not used for a long period of time, it should be charged at least once every 6 months to preserve the right capacity of the
battery. When the battery is empty, you can continue clipping by using the charger. For this purpose, insert the charger cable plug into
the plug receptacle of the clipper. You can continue clipping after 3 minutes.
HOW TO USE THE DEVICE WITH THE ATTACHED COMB
Place the comb attachment on the hair clipper. Turn on the clipper (5). Start by moving the clipper with the comb attachment against the
direction of hair growth. This step should be performed slowly and at a constant speed. Remember to systematically remove hair from
the clipper and the cutting head. Use the length adjustment wheel (3) to adjust the clipping length. You can obtain a thinning out effect by
using the thinning out adjuster (4).
TECHNICAL DATA
Power: 7W
Charging time: 8 hours
Power supply: 230V ~50Hz
TRIMMER AD 2822 (Fig. B)
1. Power switch
3. Ears and nose trimmer
USING THE DEVICE AD 2822
Trimmer for ears and nose:
Apply trimmer for ears and nose (3). Make sure that the septum and earlobe are clean before using the trimmer. Place the tip of the
trimmer into the nostril or ear to a depth no greater than 5 mm. Gently moving the turned on trimmer remove only hair protruding outside
of the ear or nose.
Trimmer for beards and mustaches:
Apply trimmer for beards and mustaches (2). Move the turned on trimmer
(Fig. A)
2. Transparent window
5. Power switch (ON/OFF)
8. Additional comb attachment
3. Length adjustment wheel
6. Comb attachment
9. Adaptor
Device is made in class II of insulation.
Device is compliant with EU directives:
2. Beards and moustaches trimmer
4. Base
against the direction of hair growth
4
Low voltage directive (LVD)
Electromagnetic compatibility (EMC)
Device marked CE mark on rating label
.