WORLD DRYER SLIMdri Manuel D'instructions page 6

After power to dryer is switched
"ON", dryer runs for approximately
30 seconds, then will not restart.
Dryer "Ghosts" (starts with no
hands present.)
Dryer air too cold.
Dryer air too hot.
Dryer air output is too slow.
Excessive Noise or Vibration
Limited Warranty
World LIMITED TEN – YEAR WARRANTY. World Warm Air Hand Dryer, Model covered in this manual, is warranted by World Dryer Corporation to the
original user against defects in workmanship or materials under normal use for 10 years after date of purchase for all components except motor brushes (3 years),
motor (5 years) and sensor (5 years). Any part which is determined to be defective in material or workmanship and returned to an authorized service location, as World
designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at World's option. For limited warranty claim procedures, see PROMPT
DISPOSITION below. This limited warranty gives purchasers specific rights from jurisdiction to jurisdiction.
LIMITATION OF LIABILITY. To the extent allowable under applicable law, World's liability for consequential and incidental damages is expressly disclaimed.
World's liability in all events is limited to and shall not exceed the purchase price paid.
WARRANTY DISCLAIMER. World has made a diligent effort to provide product information and illustrate the products in this literature accurately; however,
such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are MERCHANTABLE, or FIT FOR
A PARTICULAR PURPOSE, or that the products will necessary conform to the illustrations or descriptions. Except as provided below, no warranty or affirmation on
fact, expressed or implied, other than as stated in the "LIMITED WARRANTY" above is made or authorized by World.
PRODUCT SUITABILITY. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes,
which may vary from those in neighboring areas. While World attempts to assure that the products comply with such codes, it cannot guarantee compliance, and can-
not be responsible for how the product is installed or used. Before purchase and use of a product, review the product application, and all applicable national and local
codes and regulations, and be sure that the product, installation, and use will comply with them.
Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above limitation or exclusion may not apply to you; (b) also, some jurisdictions do not allow a limitation on how long an implied warranty lasts,
consequentially the above limitation may not apply to you; and (c) by law, during the period of this Limited Warranty, and implied warranties of implied merchantability
or fitness for particular purpose applicable to consumer products purchased by consumers, may not be excluded or otherwise disclaimed.
Manufactured by World Dryer Corporation, Berkeley, Illinois 60163 U.S.A.
PROMPT DISPOSITION. World will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to be defective
within limited warranty. For any product believed to be defective within limited warranty, first write or call dealer from whom the product was purchased. Dealer will
give additional directions. If unable to resolve satisfactorily, write to World at address below, giving dealer's name, address, date, and number of dealer's invoice, and
describing the nature of defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was damaged in transit to you, file claim with carrier.
Sensor obstruction or sensor lens
scratched or damaged.
Mounted too close to counter or
object.
Electrical noise from incoming
power supply or nearby infrared
actuated device.
Faulty circuit board (PCB)
Heater control switch is in the
""OFF"" position.
Faulty circuit board (PCB)
Faulty heating element
Excessive lint / debris build up
Excessive lint / debris build up
Loose mounting screws.
Foreign material in fan housing or
dryer outlet.
WWW.RESTROOMDIRECT.COM
Check sensor lens for foreign material or dirt. Clean lens with
soft damp cloth and mild cleaning agent. If sensor lens is
damaged or scratched, replace sensor.
Relocate the object or dryer according to installation
instructions to a minimum 18" above any reflective surface and
at least 24" from an adjacent hand dryer.
Confirm dryer base is securely grounded.
Confirm dryer is on a dedicated circuit.
Check if any nearby infrared actuated device is triggering dryer.
Replace circuit board (PCB)
Re-position heater control switch to "ON".
Place hands under sensor. Listen for PCB relay "Click.". If no
"Click" is heard, replace the PCB.
If PCB Relay "Click" is heard and dryer continues to blow cold
air, replace heating element.
See Maintenance and Cleaning Instructions (pg 5)
See Maintenance and Cleaning Instructions (pg 5)
Confirm dryer is securely mounted to wall and motor mounts to
dryer base are tight and secure.
Check and remove any foreign material in fan housing or dryer
outlet air slot.
5700 McDermott Drive
Berkeley, IL 60163 U.S.A.
800-323-0701
www.worlddryer.com
6
704 • 937• 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115