Publicité
1
Q45-BB6-LL-...
2
bn (1)
4
5
3
bu (3)
wh (2)
bk (4)
4
2
ye (5 gy)
3
1
5
Required Overcurrent Protection
WARNING: Electrical connections must be made by qualified
personnel in accordance with local and national electrical codes
and regulations.
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Supply Wiring (AWG)
Required Overcurrent Protection
20
5.0 Amps
22
3.0 Amps
24
2.0 Amps
26
1.0 Amps
28
0.8 Amps
30
0.5 Amps
ALIGNMENT
JUSTAGE
ALLINEAMENTO
REGLAGE
上
光軸調整
Up
ALINEACION
Left
左
Down
下
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or
the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purpos-
es will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other
language. For the most recent version of any documentation, refer to:www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
2
CONNECTIONS
Brown
1
+
10-30V dc
2
White
–
Blue
3
Load
4
Black
Load
5
Yellow
Laser control
Load
LOAD
(+ off; – on)
Erforderlicher Überstromschutz
WARNUNG: Die elektrischen Anschlüsse müssen von
qualifizierten Personen unter Beachtung der örtlichen und
nationalen Gesetze und Vorschriften für elektrische Anschlüsse
verbunden werden.
Überstromschutz ist erforderlich, dieser muss von der Anwendung
des Endprodukts gemäß der angegebenen Tabelle bereitgestellt
werden.
Überstromschutz kann durch externe Sicherung oder über ein
strombegrenzendes Netzteil der Klasse 2 eingerichtet werden.
Versorgungskabelleitungen < 24 AWG müssen ungespleißt sein.
Weiteren Produktsupport erhalten Sie unter
www.bannerengineering.com.
Versorgungskabel (AWG)
Erforderlicher Überstromschutz
20
5.0 A
22
3.0 A
24
2.0 A
26
1.0 A
28
0.8 A
30
0.5 A
Retro Target
反射板
Right
右
P
www.bannerengineering.com - Tel: +1 888 373 6767
ANSCHLUSS
CONNESSIONE
braun
marrone
weiß
bianco
blau
blu
schwarz
nero
gelb
gialio
Last
Carico
Protezione da sovracorrente richiesta
AVVERTENZA: I collegamenti elettrici devono essere
eseguiti da personale qualificato in conformità alle norme e ai
regolamenti vigenti a livello nazionale in materia di elettricità.
L'applicazione finale deve prevedere una protezione da sovracor-
rente come indicato nella tabella fornita.
La protezione da sovracorrente può essere assicurata da un fusi-
bile esterno o mediante limitazione di corrente, con alimentazione
classe II.
I conduttori di alimentazione con sezione < 24 AWG non devono
essere giuntati.
Per ulteriore supporto andare all'indirizzo www.bannerengineering.
com.
Cavo di alimentazione (AWG)
Protezione da sovracorrente richiesta
20
5.0 A
22
3.0 A
24
2.0 A
26
1.0 A
28
0.8 A
30
0.5 A
RACCORDEMENT
CONEXIONES
配線
brun
marrón
茶
blanc
blanco
白
bleu
azul
青
noir
negro
黒
jaune
amarilio
黄
Charge
Carga
負荷
Protection contre la surintensité requise
AVERTISSEMENT: Les raccordements électriques doivent
être effectués par du personnel qualifié conformément aux régle-
mentations et codes électriques nationaux et locaux.
Une protection de surintensité doit être fournie par l'installation du
produit final, conformément au tableau fourni.
Il est possible de fournir une protection de surintensité par un
fusible externe ou par une alimentation de classe 2, avec limitation
de courant.
Il ne faut pas raccorder des câbles d'alimentation d'un diamètre
inférieur à 24 AWG.
Pour obtenir un support produit supplémentaire, rendez-vous sur le
site www.bannerengineering.com.
Câble d'alimentation (AWG)
Protection contre la surintensité requise
20
5.0 A
22
3.0 A
24
2.0 A
26
1.0 A
28
0.8 A
30
0.5 A
必要な過電流保護
警告：有資格者が地域、および全国の電気工事規定、
規制に準拠し、電気接続を行ってください。
最終製品の用途により付属の表に従い、過電流保護を提供
しなければなりません。
過電流保護は、外付けヒューズ、または電流制限クラス2電源
で提供することができます。
24 AWG未満の電源配線リードは、接合してはなりません。
製品サポートの詳細は、www.bannerengineering.comをご覧
ください。
電源配線 (AWG)
必要な過電流保護 (アンプ)
20
5.0 アンプ
22
3.0 アンプ
24
2.0 アンプ
26
1.0 アンプ
28
0.8 アンプ
30
0.5 アンプ
Protección de sobreamperaje necesaria
ADVERTENCIA: Las conexiones eléctricas deben ser
realizadas por personal cualificado de acuerdo con las normativas
y códigos eléctricos locales y nacionales.
Se debe proporcionar protección de sobreamperaje en la apli-
cación del producto final tal como se indica en esta tabla.
La protección de sobreamperaje se puede proporcionar con
fusibles externos o con una fuente de alimentación de clase 2 con
limitación de corriente.
Los cables de suministro < 24 AWG no se pueden empalmar.
Para obtener más información sobre el producto, visite http:// www.
bannerengineering.com.
Cableado de suministro (AWG) Protección de sobreamperaje necesaria
20
5.0 A
22
3.0 A
24
2.0 A
26
1.0 A
28
0.8 A
30
0.5 A
P/N 53854 Rev. B
Publicité
