Technical Data; Standard Equipment - Virutex LR46L Mode D'emploi

is switched on.
3. Check the surface to be sanded for nails and,
before commencing work, remove any that are there.
4. Disconnect the machine from the mains before
carrying out any maintenance work.
5. Never put down an electric tool until its moving
parts have come to a complete stop.
6. Never use the sander where there is liquid, or in
very damp conditions.
7. Dust produced during sanding may be toxic or
hazardous to your health (for example, leaded paints,
some types of wood and metal). We recommend that
you always use the dust collector connection.
8. SPARE PARTS: Use only original VIRUTEX spare parts.

2. TECHNICAL DATA

MODEL LR46L
Type of machine........................ORBITAL SANDER
Power............................................................370 W
Universal Motor.........................................50-60 Hz
No-load speed........................................10000 rpm
Oscillations..................................................20000
Orbit diameter.................................................2 mm
Sanding surface........................................208x115
Weight.............................................................3 Kg
Weighted equivalent continuous
acoustic pressure level A..............................................83 dBA
Acoustic power level A................................................94 dBA
Uncertainty..............................................................K = 3 dbA
Wear ear protection!
Vibration total values.......................................a
Uncertainty...........................................................K: 1.5 m/s
MODEL LRE46L
Machine Type....ELECTRONIC ORBITAL SANDER
Power..........................................................370 W
Universal Motor.........................................50-60 Hz
No-load speed................................4000-9800 rpm
Oscillations.........................................8000-19600
Orbit diameter...............................................2 mm
Sanding surface........................................208x115
Weight..............................................................3 Kg
Weighted equivalent continuous
acoustic pressure level A..........................................83 dBA
Acoustic power level A.................................................94 dBA
Uncertainty...............................................................K = 3 dbA
Wear ear protection!
Vibration total values........................................a
Uncertainty.............................................................K: 1.5 m/s

3. STANDARD EQUIPMENT

You will find the following in the box:
- LR46L or LRE46L orbital sander
- Gr. 120 emery sandpaper sheet
- Velcro Attachment Ref. 4699209
- Dust collector bag
- Dust collector bag adapter
- Instruction manual and other documents
4. OPTIONAL ACCESSORIES AND TOOLS
1. 8646132 Perforating centring device for abrasives
2. 6446073 Standard dust collector attachment 3.5 m
3. 1746245 Dust collection connector 5 m
5. USES
Orbital sander for dry finishing of surfaces. No need to
apply pressure to the machine – Simply glide over the
surface using elliptical movements to avoid marking
or leaving hollows in the material.
In order to achieve the desired quality of finish,
sand in progressive stages using a finer grade of
sandpaper each time.
The sander comes with a forced vacuum system for
sanding dust, and a dust collection bag.
The sander is suitable for the following tasks:
Sanding furniture or other wooden surfaces
Sanding wooden floors
Sanding walls and ceilings
Removing paint from flat or contoured surfaces
: <2.5 m/s
2
h Preparing a base for painting
2
Pre-finishing of bodywork: sanding the paint filler
before applying the next layer.
6. TURNING ON THE MACHINE
AND ELECTRONIC REGULATION
To turn the machine on, press button "A" and then
activate switch "B" at the front, if necessary (Fig. 1).
To unlock the switch, press trigger "B" on the unlocking
button "X" (Fig. 1).
Model LRE46L has electronic speed control, allowing
you to work at the ideal speed for each surface and
type of disc. This makes it the perfect tool for sanding
heat-sensitive materials, which need to be sanded at
lower speeds. To regulate the speed, adjust button
"C" to the desired working speed (Fig. 1).
Place the machine on the surface to be sanded and
make the necessary movements to achieve the desired
: <2.5 m/s
2
h
2
7