Publicité
Les langues disponibles
Les langues disponibles
The memorisation procedure can be repeated up to a max. of
330 codes. When the memory is full by repeating the program-
ming operation, the CODE CH1 and CODE CH2 LEDs will start
to flash very quickly, the receiver will emit three short Beeps for
confirmation, indicating that it is not possible to store any more
codes.
Reset HW ( only in Stand Alone use) :
If the receiver must be restored to default settings (i.e. no code
memorised), press the SEL key continuously for 10 seconds.
The CH1 and CH2 LEDs will flash three times quickly and then
switch-off. The receiver will emit three long beeps for confirma-
tion.
Advanced Programming by Smartphone:
The receiver can only receive advanced pro-
gramming via Smartphone, thanks to the specific
SEAV " BeTech " app.
The app allows the installer to have a work in-
strument for all installations performed.
Once the automation has been installed, upon
request it will be possible to also configure a Cli-
ent " BeLite " App for normal use via
Smartphone for sending remote commands.
Important: it is possible to carry out advanced programming
through the BeTech application as long as no Stand Alone pro-
gramming has been carried out before.
Once the radio controls and smartphones have been memo-
rized via the BeTech application, to guarantee the exclusivity of
the system, the installer will have to change the default pass-
word, in this way, the SEL key on the receiver will be disabled
and consequently any programming possibility stand alone.
BeTech and BeLite Apps:
The SEAV "BeTech" app has a Directory where all installed
plant data is contained.
It is also used to set a Plant Name and Password (Default: 1 2
3 4 ) to subsequently access the various configurations; the
possibility of restoring a faulty receiver with a new one, reload-
ing all information contained in the app directory. Furthermore,
by entering an e-mail address, it will be possible to receive a
Back-up of all the plants in case of Smartphone failure. Option
of generating access codes to activate Client " BeLite " App.
See the Diagnostics menu for troubleshooting and much more.
The Client " BeLite " App also allows you to send commands
via Smartphone even automatically, namely you can send the
command by simply approaching the receiver.
CH1 and CH2 Operating Mode:
The receiver can manage the two channels separately and al-
so, only for CH2, allows to have different operating modes con-
by means of
figurable
the SEAV "BeTech " App:
Channel CH1: only
monostable operation.
Channel CH2: various functions available :
- Monostable ( Default )
- Bistable
- Timed ( 1 – 600 sec. ) Retriggerable
- Timed ( 1 – 600 sec. ) NOT Retriggerable
- Timed ( 1 – 600 sec. ) Resettable.
Settings :
Using the dedicated SEAV "BeTech " app via Smartphone al-
lows the receiver to manage a directory with 330 total positions
between stored Radio controls and Smartphones,which can be
programmed and/or deleted even individually.
Radio control code programming:
The receiver can store up to 330 radio controls with different
codes, such as Fix, Rolling Code or Plus.
The transmission code must be programmed as follows: press
the CODE key of the SEAV "BeTech " app via Smartphone, at
the same time send the pre-selected code of the desired radio
control; when the receiver emits a confirmation Beep,
programming will be completed. If all 330 available codes have
been stored, by repeating the programming operation, the
receiver will emit three short Beeps, indicating that it is not
possible to store any more codes.
Programming the user Smartphone:
The receiver can store up to 330 different Smartphones. To en-
able a Smartphone for operation on the receiver, download the
" BeLite " App and enter only the first activation code supplied
by the installer (generated with the BeTech App). If all 330
available codes have been stored, by repeating the program-
ming operation, the receiver will emit three short Beeps, indicat-
ing that it is not possible to store any more codes.
Deletion of Radio control/Smartphone :
The deletion of a single Radio control / Smartphone or complete
deletion can only be carried out with the SEAV "BeTech " App,
by accessing the Directory of the plant and selecting weather
you want to delete a single Radio control/smartphone or all of
them. The receiver will emit two long Beeps for confirmation,
preceded by a series of visible communications on the
Smartphone.
Programming by Remote RCD :
Using the dedicated SEAV "BeTech" App via Smartphone, it is
possible to select the radio control Programming function re-
motely via a radio control already present in the memory: The
Radio control can be programmed remotely as follows: continu-
ously sending a previously-stored radio control code for more
than 10 seconds. At this point the control unit switches to pro-
gramming mode, as described above in the paragraph "RCD
Stand Alone programming".
CH2 ( in Pgm remote mode, operation is only
Caution :
monostable).
Reset :
The control unit can be used to reset it to default settings
through the dedicated SEAV "BeTech" app; press RESET on
the Smartphone and the receiver will emit three long Beeps for
confirmation at the same time.
Diagnostics :
Using the dedicated SEAV "BeTech" App, the control unit al-
lows for the Real time monitoring of the status of all OUTPUTS,
the number of radio controls present in the Memory and their
Type and other information useful to the installer.
Rev. 1.2 29/06/2022
Publicité
