Technical Specifications; Operating The Appliance; Cleaning And Maintenance - Arnica BORA 4000 Manuel D'utilisation

III. TECHNICAL SPECIFICATIONS
Model
Voltage
Power
Cord Length
Used Life
Electrical Insulation class : II
IV. PREPARING FOR USE
• ATTENTION – Do not insert the mains plug into the wall socket
until the appliance is completely ready for use.
• Lift the Reservoir Group and put aside by holding from its
handle.
• Remove the water filter tube and Water Filter Body by pulling
after you open the reservoir cover.
• Check the parts and accessories in the Operating Manual with
the ones you take out of the Tank. Check whether they are
missing or damaged.
• If you will use your vacuum cleaner immediately, add water in
the Transparent Water Tank in accordance with the maximum
level (Maximum 1.2 liter) indicated on the Tank.
• Drop 2 or 3 drops of perfume supplied with your vacuum
cleaner into the water for providing your room's air smells
good.
• Replace the Water Filter Body and water filter tube to their
places in the Transparent water tank. Please do not forget
the replace Water filter tube loophole to the water filter tube.
Replace the water tank Cover.
• Replace the Transparent Reservoir Group on the main Body
tightly.
• In order to connect the Hose Group to the Main Body Group,
place the Vacuum Head of the Hose on to the Vacuum Head on
the tank.
WARNING: Do not ever vacuum wet floors or water from sink.
Only perform dry vacuuming with your vacuum cleaner.
V. OPERATING THE APPLIANCE
• Perform the Assembly and Preparation for Use processes.
• Choose the most appropriate accessories for your purpose and
affix these accessories directly on the gun section or affix the
Extension tubes first and then accessories on their ends.
• For an effective cleaning, use the accessories as mentioned in
the following.
» Main brush for vacuuming carpets, rugs and hard
grounds.
» Crevice nozzle for cleaning the dusts, chips and etc. at
radiators, drawers and etc. narrow sections.
» Directly the Extension Tube for cleaning soil, debris, chips, feathers
and etc.
» The Small brush Accessories for cleaning racks, clothes,
electronic devices, lampshades, furniture, curtains and
etc.
» Round brush for cleaning curtains or dusting.
» The hard ground brush for cleaning dust and etc. on the
hard grounds such as parquet.
: BORA 4000
: 220-240V~, 50-60Hz
: 2400W Max.
: 6m.
: 10 years
• Plug in your vacuum cleaner and start it by pressing the On-
Off Button.
• After completing the vacuuming process, turn off your vacuum
cleaner by pressing the On-Off Button. Unplug your vacuum
cleaner and furl the cord by pressing Cord Spinning button.
For some models, for furling the cable, it will be sufficient to
hold and pull the cord lightly. This specification can vary in
accordance with the model.
VI. CLEANING AND MAINTENANCE
• You have to unplug your device, before beginning any Cleaning
or Maintenance processes.
• After every use, empty the water in the Transparent Water Tank
and clean and dry the tank.
• Do not ever leave your vacuum cleaner with liquid and dirt in
it for hygienic purposes and extending the life of your vacuum
cleaner.
• Pull and remove the Water Filter Body and the engine air inlet
neck. The Water Filter Body and the engine air inlet neck can
be washed with warm and soapy water or under tap water. Dry
after you wash these parts before replacing them.
• The cleanness of hepa filter should be checked periodically.
Clean the filter if it is not clean. This filter loses its
characteristics after a certain usage period and requires
replacing.
• Carry your vacuum cleaner by holding from its Body Handle.
• Just use original parts and accessories for efficient cleaning
and lifecycle and warranty of your device. Provide the
accessories and parts from the closest Authorized Service
when it is required.
WARNING: Only perform dry vacuuming with your vacuum cleaner.
WARNING: If there is any damage on the plug, please contact with
after sale service or distributor. The plug must be changed expert
who knows the product well.
WARNING: Please do not add less or more water than max level as
shown at the transparent water tank. If you add less water; than
max. level this can be caused that dust goes the motor. If the water
is added more than max level, water will go the motor. To protect
your vacuum cleaner, water should be added at max level.
7