Connettori; Connecteurs - Fbt X-LITE 115 A Mode D'emploi

Table des Matières

Publicité

ITA

CONNETTORI

FRA

CONNECTEURS

SPEAKON è un connettore adatto appositamente per il collegamento tra finali
di potenza e altoparlanti; inserendolo nell'apposita presa si blocca in modo da
impedire un distacco accidentale; inoltre è dotato di protezione contro scosse
elettriche e garantisce una corretta polarizzazione.
SPEAKON is a connector wich is specially adapted for connecting power terminals
to loudspeakers; when inserted in an appropriate socket it locks so as to prevent
accidental disconnection; moreover, it is equipped with protection against electrical
shocks and guarantees the correct polarisation
Les connectecteurs SPEAKON a été spécialement conçu pour le branchement des
terminaux de puissance et des hauts-parleurs. Placé dans la prise adéquate, il sert
à prévenir un débranchement accidentel. De plus, il est pourvu d'un systéme de
protection contre les secousses électriques te garantit un niveau de polarisation
correct.
SPEAKON ist ein Eingang, der extra für die Verbindung zwishen Leistungsenden
und Lautsprechers angepasst wurde. Wenn er in die entsprechende Buchse
eingesteckt wird, dann blockiert er so, dass er nicht ungevollt herausgezogen
werden kann. Er ist außerdem mit einem Stromschlagschutz ausgerüstet und
gewälhrleistet die richtige Polarisation.
I JACK sono connettori tipici per trasportare due segnali separati di due canali,
destro e sinistro, con un unico connettore e quindi possono essere di tipo mono
o stereo. I jack mono (TS), detti anche sbilanciati, si differenziani da quelli stereo
(TRS), o bilanciati, per la loro composizione. I primi hanno lo spinotto diviso in due
parti, punta e massa (Tip e Slave), a cui sono collegati i due poli; i jack stereo o
bilanciati sono invece divisi in tre parti, in quanto hanno un anello centrale (Ring)
collegato ad un secondo filo che costituisce il terzo polo (negativo).
I connettori XLR hanno tre poli e vengono utilizzati quasi sempre per condurre
segnali molto bilanciati: i tre poli corrispondono rispettivamente alla massa (1), al
segnale positivo (2) e al segnale negativo (3).
The 3-pole XLR connectors are almost always used for conducting mono-
balanced signals; the three poles correspond respectively to ground (1), the
positive signal (2) and the negative signal (3).
Les connectecteurs XLR possèdent trois pôles et servent, en général, a trasmettre
les signaux mono balancès; le trois pôles correspondent, dans l'ordre à la masse
(1), au signal positif (2) et au signal négatif (3).
Die XLR-Eingänge haben drei Pole und werden fast immer zur Übertragung von
ausgeglichenen Mono-Signalen benutzt; die drei Pole entsprechen jeweils der
Masse (1), dem positiven signal (2) und dem negativen Signal (3).
The JACKS are typical connectors for the transporting of two separate signals
through two channels, left and right, using a single connector and therefore they
can be either mono or stereo. Mono jacks (TS) also known as unbalanced jacks,
are recognisable from stereo or balanced jacks (TRS) by their composition. The
point of the mono jacks is divided into two parts, tip and ground Tip and Slave) to
which the two poles are connected; the stereo or balanced Jacks are divided in
three parts, as they have a central ring (Ring) which is connected to a second wire,
the third (negative) pole.
Les prises JACK sont des connecteurs typiques et servent à transporter les deux
signaux séparés des deux canaux, droite et gauche, à travers un seul et unique
connecteur. lls peuvent etre de type mono ou stéréo. Les prises mono (TS),
appelés aussi non balancées, de par leur composition, se distinguent de celles
stéréo (TRS) ou balancées. En effet, les premières ont la prise divisée en deux
parties, pointe et masse (Tip et Slave), auxquelles les deux pôIes sont branchés.
Par contre, les prises jack stéréo ou balancées sont divisées en trois parties :
elles possèdent une bague centrale (Ring), à laquelle (TRS) est branché à un
deuxième fil qui constitue le troisième pôIe (pôIe négatif).
Die JACK sind typische Eingänge (Klinke), um zwei getrennte Signalen von
zwei Kanälen , rechts und links, mit einem einzigen Eingang zu übertragen und
können von daher Mono oder Stereo sein. Die Mono Jacks ( TS), auch als nicht
ausgeglichen bez e i c h n e t , unterscheiden sich in ihrem Aufbau von den Stereo-
Jacks (TSR) bzw. den ausgeglichenen Klinkensteckern. Die ersten haben einen
zweigetei/ten Stift, Leiter und Masse (Tip und Slave), an denen die beiden Po/e
angesch/ossen sind. Die Stereo- bzw. die ausgeg/ichenen Jacks bestehen aus
drei Teilen, da sie eine zentrale Spule (Ring) haben, an denen (TRS) an einen
zweiten Draht angeschlossen ist, der den dritten Poi bildet (negativer Poi).
UK
CONNECTORS
DEU
ANSCHLÜSSE
8

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

X-lite 110 aX-lite 112 aX-pro 115 aX-pro 110 aX-pro 112a

Table des Matières