Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51080F
Wrenches: 19mm
Drill Bits: None
j
Flat Washer, 1/2"
Qty. (6)
k
Lock Washer, 1/2"
Qty. (6)
For vehicles with appearance panel:
Remove appearance panel which covers the trunk pan. This panel will need to be trimmed or not reinstalled on vehicle. Ask vehicle
owner their choice before starting installation. See Figure 2
1.
Lower the exhaust by detaching it from the rubber isolator.
2.
Raise hitch into position and install hex bolts, lock washers and flat washers into existing weldnuts in frame, as shown above.
3.
Raise exhaust back into position and reattach to the rubber isolator.
4.
Reinstall trimmed cover panel removed. Or return untrimmed panel to vehicle owner.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2010, 2011, 2012 Cequent Performance Products
Installation Instructions
Toyota Sienna
Toyota Sienna
2011 and newer models: Hitch crosstube is visible beneath
bumper with a more than normal gap between fascia and crosstube.
Fascia
Frame Rail
Existing Weldnut
3 Places
(Both Sides)
Note:
Fasteners Typical
Both Sides
Figure 1
Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Sport Model
Area to be trimmed
Qty. (6)
Hex Bolt, M12 x 1.25 x 40mm
Sheet 1 of 3
51080N
Part Numbers:
51080
97080
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
5,000
500
3,500
350
To be reinstalled
Area to be trimmed
Figure 2
To be reinstalled
2-1-12
Rev. D
Publicité
Manuels Connexes pour Cequent Performance Products 51080
Sommaire des Matières pour Cequent Performance Products 51080
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007, 2010, 2011, 2012 Cequent Performance Products Sheet 1 of 3 51080N 2-1-12 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2007, 2010, 2011, 2012 Cequent Performance Products Feuille 2 de 3 51080N 2-1-12 Rev.
- Page 3 Este producto cumple con las especificaciones y requerimientos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007, 2010, 2011, 2012 Cequent Performance Products Hoja 3 de 3 51080N 2-1-12 Rev.