Cleaning Instructions; Avertissements - Livington Touchless Mop XXL Guide Rapide

Masquer les pouces

Table des Matières

Les langues disponibles

auseinandernehmen und ineinandergesteckt

aufbewahren: das spart Platz.

4 o d m U

Thank you for purchasing Livington Touchless Mop

XXL, the mop that is cleaned and dried in one bucket

with two separate compartments: one for cleaning,

the other for drying. To ensure correct use, please

read the instruction manual thoroughly. Keep this

manual to hand for future reference.

WARNING

• Do not use the product if it is in

poor condition or defective.

• Keep the product out of reach of

children.

• Insert the microfiber mop after

the head has been mounted.

• The Livington Touchless Mop XXL

is only suitable for household use.

ASSEMBLY INSTRUCTIONS

Step 1: Put together the four handle elements and

snap the opening of the smallest handle element into

the mop head (ill. 1).

Step 2: Attach the end of the microfiber pad to the

corresponding end of the rotatable head. WARNING!

BE SURE TO ATTACH THE THREE RUBBER

STRAPS OF THE MICROFIBER PAD TO THE MOP

HEAD USING THE RUBBER LOOPS PRIOR TO

ATTACHING THE ENTIRE MICROFIBER PAD WITH

A QUICK RELEASE (SEE ALSO ILL. 2). Attach

the microfiber pad to the mop head using the velcro

fastener as shown in the illustration.

Step 3: Connect the two bucket segments in the

middle. Use the sliding guides present for this (ill.

3). Fix the bucket with the screw cap by turning the

attachment in the opposite direction (ill. 4).

NOTE: Ensure that the plastic fastenings are correctly

affixed to the respective buckets (ill. 7).

Step 4: Attach the cleaning cover (labeled „WASH")

to the bucket that is also marked WASH. Affix the

drying cover (labeled „DRY") in the same way (ill.

3). Make sure that the handles of the buckets are

in place. Ensure that you have placed the „Wash"

cleaning cover on the „Wash" bucket and the „Dry"

cleaning cover on the „Dry" bucket (see ill. 3).

Step 5: Insert the transparent sealing plugs into the

M19166_Livington Touchless Mop XXL_Manual_20190722_BS.indd 4

Hergestellt in China

respective bucket segment openings to prevent any

water from leaking (ill. 5).

INSTRUCTIONS FOR USE

Step 6: Fill the bucket intended for the cleaning

process (WASH) with water (with or without cleaning

agent) up to the filling limit on the inside. In order

to prevent streaking, do not use bleach or strong

foaming agents (such as washing-up liquid). Please

make sure to fill the bucket up to the maximum

filling limit so that the microfiber pad is sufficiently

moistened. Top up the water as necessary (ill. 8).

Step 7: Position the mop upright so that it can be

inserted into the respective slot opening (ill. 9).

Step 8: To rinse, insert the mop into the WASH opening,

hold the handle firmly and move the mop up and down

as much as necessary until it is flushed clean (ill. 10).

Step 9: Then move around in the DRY port as much

as is required to squeeze the water out of the mop.

Repeat the process until the pad reaches the desired

level of dryness. You can clean any surface you want.

For best results, repeat these procedures as often as

necessary. Upon completion, drain the water from

the bucket segments by removing the clear plugs or

simply pour out the contents.

TIP: We recommend emptying the bucket by removing

the stopper plugs in a bathtub or shower cubicle.

NOTICE

The Livington Touchless Mop XXL works perfectly on

hard floors of all kinds, such as tiles, linoleum, wood,

laminate, parquet, marble, granite, etc.