Before Starting The Equipment; Assembling The Components; Technical Data - Bavaria BPM 40 P Instructions De Montage Et Mode D'emploi

Anleitung_BPM_40_P_SPK7__ 11.02.14 09:16 Seite 23
hours, during which time the machine is primarily
used to maintain small-scale, residential lawns and
home/hobby gardens. Public facilities, sporting halls,
and agricultural/forestry applications are excluded.
Bitte beachten Sie, dass unsere Geräte
bestimmungsgemäß nicht für den gewerblichen,
handwerklichen oder industriellen Einsatz konstruiert
wurden. Wir übernehmen keine Gewährleistung,
wenn das Gerät in Gewerbe-, Handwerks- oder
Industriebetrieben sowie bei gleichzusetzenden
Tätigkeiten eingesetzt wird.
The operating instructions as supplied by the
manufacturer must be kept and referred to in order to
ensure that the lawn mower is properly used and
maintained. The instructions contain valuable
information on operating, maintenance and servicing
conditions.
Important! Due to the high risk of bodily injury to the
user, the lawn mower may not be used to trim
bushes, hedges or shrubs, to cut scaling vegetation,
planted roofs, or balcony-grown grass, to clean (suck
up) dirt and debris off walkways, or to chop up tree or
hedge clippings. Moreover, the lawn mower may not
be used as a power cultivator to level out high areas
such as molehills.
For safety reasons, the lawn mower may not be used
as a drive unit for other work tools or toolkits of any
kind.

4. Technical data

Engine type:
Single cylinder four-stroke engine, 99 ccm
Engine power:
Working speed:
Fuel:
Tank capacity:
Engine oil:
Spark plug:
Electrode spacing:
Cutting height adjustment: dezentral, (35/50/65 mm)
Cutting width:
L sound pressure level:
pA
K uncertainty
pA
L sound power level:
WA
Vibration a
hw
K uncertainty
Weight:

5. Before starting the equipment

5.1 Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
5.1.1 Fitting the push bar
1. Take the mower and attachment parts out of the
2. Now screw the upper push bar to the lower push
3
3. Fasten the lower push bar to the mounts on the
1.3 kW/1.8 HP
4. Then hook the starter cord in the starter cord
3000 min -1
standard petrol
5. Fasten the cable clip to the lower push bar (Fig.
approx. 0.7 l
6. Hook the grass basket into the mounts on the
approx. 0.4 l / 15W40
F7 RTC
5.1.2 Fitting the wheels
0.6 mm
For details of how to fit the wheels, please refer to
5.1.3 Adjusting the cutting height.
400 mm
5.1.3 Adjusting the cutting height
82,2 dB(A)
(Fitting the wheels, see point 3-5)
3 dB
96 dB(A) Important! Adjust the cutting height only when
the engine is switched off and the spark plug
7.33 m/s 2
connector has been pulled off.
One Philips screwdriver
One ring wrench size 15
One flat oil drip tray (for changing the oil)
One 1 liter measuring jug (oil/petrol resistant)
One petrol can
One funnel (suitable for the tank's petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
One petrol suction pump (plastic, available from
DIY stores)
One oil can with hand pump (available from DIY
stores)
0.4 liter of engine oil (15W-40)
packaging and check that all parts are present
(Fig. 2-3).
bar (Fig. 4-5). Pull the cords over the star nut so
that they do not get kinked when the push bar is
swung down.
mower housing (Fig. 6-9).
guide (Fig. 10)
11).
mower (Fig. 12).
GB
1.5 m/s 2
17 kg
23