Johnson Controls tyco HSM3WiFi Mode D'emploi

HSM3WiFi USB-to-WiFi Adapter
Introduction
The HSM3WiFi USB-to-WiFi Adapter provides a secure, temporary wireless connection between the HS3032, HS3128, or
HS3248 alarm panel and a mobile device or computer. The alarm panel settings can be configured wirelessly using the
available installation App or DLS-5.
The HSM3WiFi USB-to-WiFi Adapter is intended to be used during initial installation and configuration, then removed and
taken to additional sites.
Note: Installation shall be carried out by qualified persons only.
Installation
Before using the HSM3WiFi USB-to-WiFi Adapter, it is recommended to change the default SSID and Password for added
security.
1. Plug the HSM3WiFi USB-to-WiFi Adapter into a PC.
2. Open DLS-5.
3. Change the SSID and password using WiFi Configuration under Tools in the menu bar.
Note: The default SSID and password are printed on the product label.
To customize alarm panel settings complete the following steps:
1. Plug the HSM3WiFi USB-to-WiFi Adapter into the USB connector on the alarm controller. This triggers a panel
trouble, USB Wi-Fi Connected, as a reminder to remove the HSM3WiFi USB-to-WiFi Adapter before leaving the
site.
2. On a laptop or mobile device, use the operating system setting to connect to the HSM3WiFi USB-to-WiFi Adapter
as a standard Wi-Fi network.
3. If using the installation App, an integration session must be enabled on the panel using a system keypad. In
Installer Programming mode, enable one of the 4 available integration sessions for USB in section [851][425],
[452], [479] or [506] by turning on option [1], Integration over USB.
4. If using DLS-5, ensure that none of the 4 integration sessions are enabled for Integration over USB.
To connect to the panel using the installation App, copy the Integration ID and Access Code, found in the panel locations
listed below, into the App.
1. [851]>[422] - 12-digit integration ID number.
2. [851]>[423], [450], [477], or [504] (depending on if using sessions 1 to 4) - 32-digit Integration Access Code.
To connect to the panel using DLS-5, complete the following steps:
1. Create a new account and select IP as the Connection Type.
2. Set the IP address to 192.168.55.1.
When configuration is complete, remove the HSM3WiFi USB-to-WiFi Adapter from the alarm panel. This clears the panel
USB WiFi Connected trouble.
Note: Keep the number of walls and ceilings between the HSM3WiFi USB-to-WiFi Adapter and your mobile device to a
minimum. Each wall or ceiling can reduce the HSM3WiFi USB-to-WiFi Adapter's range.
Note: Keep away from electrical devices or appliances that generate RF noise.
Specifications
Spectrum IEEE 802.11 b/g/n
Frequency band 2.4 GHz
Security WPA2
Supply voltage USB VBUS 5 VDC ± 5 %
Current 120 mA @ 5 V (typical); 380 mA @ 5 V (maximum)
Panel interface USB Type-A, Male
RF distance > 20 m line of sight (in the metal panel cabinet with the door open)
Default SSID HSM3WIFI
Default password 12345678
Static IP address 192.168.55.1
Compatibility
Alarm panel HS3032 and HS3128 v1.0 or higher, and HS3248 v1.10 or higher
Operating system Android v4.4 and higher
iOS v8 and higher
Windows 7, 8.1, 10
PC software DLS-5 v1.7 and higher
App ConnectAlarm
Regulatory Information
FCC MODIFICATION STATEMENT - Digital Security Controls has not approved any changes or modifications to this device
by the user. Any changes or modifications could void the user's authority to operate the equipment.
Digital Security Controls n'approuve aucune modification apportée à l'appareil par l'utilisateur, quelle qu'en soit la nature.
Tout changement ou modification peuvent annuler le droit d'utilisation de l'appareil par l'utilisateur.
FCC AND ISED CANADA INTERFERENCE STATEMENT - This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device. This device complies with ISED Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radio électrique subi, même si le brouillage est susceptible d'en comprom-ettre le fonctionnement.
FCC CLASS B DIGITAL DEVICE NOTICE -This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced radio/television technician for help.
CAN ICES-3 (B) / NMB-3 (B).
FCC/ISED CANADA WIRELESS NOTICE
This equipment complies with FCC and ISED Canada radiation exposure limits set forth for an uncontrolled environment. The
device should be installed and operated with minimum distance of 20 cm between the radiator and your body.
Cet appareil est conforme aux limites d'exposition aux ray-onnements de la ISED Canada pour un environnement non contrôlé.
Cet appareil doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et
votre corps.
Model HSM3WIFI contains M/N: SPWF04SA with FCC ID: S9NSPWFS04 and IC: 8976C-SPWFS04.
Limited Warranty
Digital Security Controls (DSC) warrants that for a period of 12 months from the date of purchase, the product shall be free of
defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, DSC shall, at its
option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to
defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the
control of DSC such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse,
alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and
shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part
of DSC. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its
behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no
event shall DSC be liable for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other
losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product. WARNING:
DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to,
but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.
Important Information: Changes/modifications not expressly approved by DSC could void the user's authority to operate this
equipment.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is
purchased under the following license terms: This End-User License Agreement ("EULA") is a legal agreement between You
(the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, a
division of Tyco Safety Products Canada Ltd. ("DSC"), the manufacturer of the integrated security systems and the developer
of the software and any related products or components ("HARDWARE") which You acquired. If the DSC software product
("SOFTWARE PRODUCT" or "SOFTWARE") is intended to be accompanied by HARDWARE, and is NOT accompanied by
new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes
computer software, and may include associated media, printed materials, and "online" or electronic documentation.
IMPORTANT READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is
purchased under the following license terms:
This End User License Agreement ("EULA") is a legal agreement between You (the company, individual or entity who
acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd.
("DSC"), the manufacturer of the integrated security systems and the developer of the software and any related products or
components ("HARDWARE") which You acquired.
29010219R002
If the DSC software product ("SOFTWARE PRODUCT" or "SOFTWARE") is intended to be accompanied by
HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE
PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed
materials, and "online" or electronic documentation.
Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end user license
agreement is licensed to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree
unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous
arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE
PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other
intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE. This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE
PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used
concurrently on or from different computers, including a workstation, terminal or other digital electronic device
("Device"). In other words, if You have several workstations, You will have to acquire a license for each workstation
where the SOFTWARE will be used.
(c) Backup Copy - You may make back up copies of the SOFTWARE PRODUCT, but You may only have one copy per
license installed at any given time. You may use the back up copy solely for archival purposes. Except as expressly
provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed
materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or
disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by
applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the
written permission of an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software
Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not
be separated for use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE
PRODUCT is licensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT
may only be used with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post
it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or
transfer of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including
all component parts, the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to
the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of
the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms
and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its
component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or
its suppliers.
3. COPYRIGHT
All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images,
photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies
of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying
the SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which may be accessed through
use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable
copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights
not expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS
You agree that You will not export or re export the SOFTWARE PRODUCT to any country, person, or entity subject to
Canadian export restrictions.
5. CHOICE OF LAW: This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
6. ARBITRATION
All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance
with the Arbitration Act, and the parties agree to be bound by the arbitrator's decision. The place of arbitration shall be
Toronto, Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
©2019 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO and DSC are
trademarks and/or registered trademarks.
Unauthorized use is strictly prohibited.