Removing/Inserting The Battery - Milwaukee MXF370 Manuel De L'utilisateur

SYMBOLOGY
Volts
Direct Current
Vibrations per Minute (VPM)
Read operator's manual
Wear personal protective equipment
(PPE) according to the job site
PPE
requirements.
Wear eye protection
Pairing
Cold Start LED
Remote mode
OFF position
ON position
UL Listing for Canada and U.S.
US
C
SPECIFICATIONS
Cat. No. .....................................................MXF370
Battery Type ........................................ MX FUEL™
Charger Type....................................... MX FUEL™
Module/FCC ID ............................ BGM11S/QOQ11
Recommended Ambient
Operating Temperature ...................... 0°F to 125°F
MX FUEL Li-Ion Battery Packs ............ 72 V DC
TM
Rated VPM ...................................................11,200
Weight (Tool-Only) ......................................12.2 lbs
Weight (With MXFXC406 battery pack,
21" flex shaft and 2.5" head) ................... 51.2 lbs
MILWAUKEE Flex Shafts and Heads
7' Flex Shaft .........................Cat. No. 48-37-7007
10' Flex Shaft .......................Cat. No. 48-37-7010
14' Flex Shaft .......................Cat. No. 48-37-7014
21' Flex Shaft .......................Cat. No. 48-37-7021
1" Head ................................Cat. No. 48-37-5010
1-1/2" Head .........................Cat. No. 48-37-5015
2" Head ................................Cat. No. 48-37-5020
2-1/2" Head .........................Cat. No. 48-37-5025
Remote Cat. No. .............................................3701
FCC ID .....................................................P36-3701
IC ......................................................... 25187-3701
Communication Range ............................. Up to 30'
Battery Type..................................................2xAAA
DC Input Volts..................................................3.0 V
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push the battery latch lock
to the side and squeeze the battery latch lever. Pull
the battery pack away from the machine.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body of
the machine. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this machine.
Others may be hazardous.
Attaching the Flex Shaft
Flex shafts are normally lubricated from the manu-
facturer from one end. Attach the greased end to
the machine. Use a flex shaft with a length suitable
for the job.
1. Remove the battery pack. WARNING! Always
remove battery pack before changing or removing
accessories.
2. Open coupler locking handle.
3. Place the flex shaft into the coupler.
4. Pull the flex shaft until the coupler locking handle
engages. (Handle will automatically fall into place
with an audible click).
Attaching Head to Flex Shaft
1. Remove the battery pack. WARNING! Always
remove battery pack before changing or removing
accessories.
2. Coat flex shaft threads with sealant to prevent
water from entering head
3. Thread head onto flex shaft.
4. Tighten by gripping metal portion of the flex shaft
and flats of the head.
Changing Remote Batteries
Only use alkaline batteries. Do not use zinc-carbon
batteries. If the remote will not be used for a long
time, remove the batteries as a protection against
corrosion.
To change the batteries:
1. Open the battery compartment.
2. Insert the batteries according to the polarity
marked in the compartment.
3. Close the battery compartment.
Pairing the Remote
1. Arm the machine.
2. On the machine, set the switch to the
3. Turn on the remote.
4. On the machine, press and hold the
until LED begins flashing (indicating machine is
ready to pair).
5. Press and hold the
flashing LED on machine will turn solid then
off when the remote has paired successfully.
NOTE: Remote needs to be within close proximity
to ensure remote is receiving signal from the ma-
chine. This procedure will time out in 30 seconds
if machine is not paired.
4
position.
button
button on the Remote;