Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Comark Handheld Thermometers
C12 HACCP,
C20 and Catercheck 3
Operator Manual
Overview of Display Symbols
A – Main Display for Temperature
B – °C Indicator
C – Sensor Type – PST (Thermistor)
D – Low Battery Indicator
Connecting Probes to the Thermometers
The C12 and C20 thermometer have sockets for probe
connection of Thermistor probes.
Switching On and Off
The single 'ON/OFF' button on the keypad is used to switch
on the thermometer. After a short pause the display will show
the model of the instrument and will then revert to normal
temperature display.
Description
C series thermometers have a high strength, polycarbonate
case with rubber over moulding to provide durability and
protection against dust and water ingress
The Catercheck 3 is based on the C20 but has a fixed probe.
C12 HACCP Thermometer
The C12 Thermometer comes complete with colour coded
labels so that you can change the colour from blue to red,
green, yellow or orange.
Instructions
Should you wish to change the blue label on your C12
thermometer from the blue label supplied, remove the plastic
protective cover from the C12 Label at the front of the
instrument (if fitted). It is not necessary to remove the label
itself. Select the new coloured label and carefully remove the
backing cover to reveal the glued area. Carefully align the
label over the old one and affix into place.
The air and penetration probes provided do not have colour
coding.
1
Auto Switch Off/Power Saving Mode
C12 and C20 series thermometers have auto-switch off
feature. This is set to 3 minutes.
Care of the Thermometer
C12 and C20 series thermometers are dust and waterproof as
stated in the specifications and will withstand harsh
environments. Use a damp cloth or warm soapy water to
remove deposits and prevent them from hardening or
becoming sticky. Do not use solvent-based cleaners or
methylated spirit, etc.
C20
In particularly harsh environments care should be taken to
clean the Lumberg probe connector regularly. This should
ensure it does not become difficult to remove the probe from
the thermometer. The probe should be removed from the
instrument as frequently as necessary, the thread then
cleaned and lubricated with food safe oil.
Caution: Do not place any C12 or C20 series thermometers in
a dishwasher.
Changing the Batteries
The symbol BAT appears on the display when the battery
voltage has reduced. Battery replacement is recommended at
this time.
To replace the battery, remove the battery cover retaining
screw on the rear of the instrument, using the correct size
screwdriver. Remove the two cells, and replace with alkaline
cells only. Be careful to observe the correct polarity. Take
care not to over-tighten the screw when refitting the cover.
Note: The C12 and C20 series thermometers will not work if
the battery compartment is incorrectly fitted or missing. In this
instance the display will show 'OPEn'. Please note the small
pip on the inside of the battery cover, which must fit into the
hole provided in the back of the case.
3
2
Trim folded width to
Importør:
63mm
Impex Produkter AS
Gamle Drammensvei 107
1363 Høvik
www.impex.no
info@impex.no
Tel.: 22 32 77 20

Publicité

loading

Sommaire des Matières pour Fluke COMARK C12 HACCP

  • Page 1 Trim folded width to Description Importør: 63mm Impex Produkter AS C series thermometers have a high strength, polycarbonate case with rubber over moulding to provide durability and Gamle Drammensvei 107 protection against dust and water ingress 1363 Høvik The Catercheck 3 is based on the C20 but has a fixed probe. www.impex.no C12 HACCP Thermometer info@impex.no...
  • Page 2 Specifications for C12, C20 and Catercheck 3 Sensor Thermistor 10 K Ohms uni-curve Connector C12: 3.5mm Jack C20: 6-pin Lumberg Measurement Range -40°C to +125°C Scale °C Displayed Resolution 0.1° System Accuracy at 23°C ±0.5°C -20°C to +70°C Ambient Temperature Range -20°C to +50°C operating Thermomètres portables Comark Display...
  • Page 3 Mode Arrêt automatique/Economie d'énergie Caractéristiques des C12, C20 et Catercheck 3 Les thermomètres série C12 et C20 comportent une fonction d'arrêt automatique programmable. Elle est réglée sur 3 Capteur Thermistor 10 KOhms uni-curve minutes. Connecteur C12: Jack 3,5 mm C20 : Lumberg 6 broches Entretien du thermomètre Gamme de mesure...
  • Page 4 Übersicht der Anzeigesymbole Abschaltautomatik/Energiesparmodus Die Thermometer der Reihen C12 und C20 verfügen über eine Abschaltautomatik. Diese ist auf 3 Minuten voreingestellt. Pflege des Thermometers Die Thermometer der Reihen C12 und C20 sind gemäß den technischen Daten staubgeschützt und wasserdicht und widerstehen selbst härtesten Beanspruchungen.
  • Page 5 Descripción Descripción de los símbolos de la pantalla Los termómetros de la serie C tienen una carcasa de policarbonato de gran resistencia con una moldura de goma para mayor durabilidad y protección contra el polvo y la entrada de agua. El modelo Catercheck 3 se basa en el modelo C20 pero tiene una sonda fija.
  • Page 6 Comark Instruments 52 Hurricane Way, Norwich, Norfolk, NR6 6JB Tel: +44 844 815 6599 Fax: +44 844 815 6598 www.comarkinstruments.com Comark Instruments PO Box 9090 Everett, WA 98206 Tel (503) 643 5204 Fax (503) 644 5859 www.comarkUSA.com Copyright  Comark Instruments Part No.

Ce manuel est également adapté pour:

Comark c20Comark catercheck 3