Technical Data; Troubleshooting Guide; Declaration Of Conformity - Kärcher BLV 18-200 Battery Manuel D'instructions Original

Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device does not start
up
The device stops during
operation
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

Device performance data
Nominal voltage
Average air speed of cordless
blower
Average air speed of cordless
blower (turbo mode)
Maximum theoretical air speed of
cordless blower
Maximum theoretical air speed of
cordless blower (turbo mode)
Average air speed of cordless
suction device
Average air speed of cordless
suction device (turbo mode)
Maximum theoretical air speed of
cordless suction device
Maximum theoretical air speed of
cordless suction device (turbo
mode)
Mulch ratio
Collecting bag volume
Dimensions and weights
Weight (without battery pack)
Length x width x height

Troubleshooting guide

Cause
Battery pack is not inserted correctly.
Battery pack is empty
Battery pack is defective.
Safety button did not trip during assem-
bly.
The battery has overheated
Motor has overheated
BLV 
18-200
V 18
km/h 152,9 +/-
10 %
km/h 186,7 +/-
10 %
km/h 186,7 +/-
10 %
km/h 262,9 +/-
10 %
km/h 112,7 +/-
10 %
km/h 135,2 +/-
10 %
km/h 138,4 +/-
10 %
km/h 162,6 +/-
10 %
10:1
l 45
kg 3,5
mm 1243 x
171 x 376
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Push the battery pack into the mounting
until it latches into place.
 Charge the battery pack.
 Replace the battery pack.
1. Unscrew the suction pipe fixing screw once
again.
2. Tighten the suction pipe fixing screw until a
clicking sound is heard.
The safety button has tripped.
 Stop working and allow the battery to cool
down to normal battery temperature.
 Stop working and allow the motor to cool
down.
Determined values in acc. with EN 50636-2-100
Sound level L Cordless blower dB(A)
pA
Sound level L Cordless blower/
pA
vacuum
Uncertainty K
pA
Sound power level L
tainty
WA
Total vibration value for cordless
blower
Total vibration value for cordless
blower/vacuum
Uncertainty K
Subject to technical modifications.
WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Device with a hand-arm vibration value > 2.5 m/s²
(see chapter Technical Data in the operating
CAUTION
for several hours can lead to numbness. ● Wear warm
gloves to protect your hands. ● Take regular breaks
from work.

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
English
dB(A)
dB(A)
+ K uncer- dB(A)
WA
2
m/s
2
m/s
2
m/s
Vibration value
instructions)
● Uninterrupted use of the device
BLV 
18-200
87,6
90,8
3,0
107
3,0
3,5
1,5
17