Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
INSTALLATION MANUAL
784EC Edgemont Craftsman Front Kit
with Backing Plates 799BPB-1, 799BPB-2 or 799BPB-3 (sold separately)
Use with Valor G4 780 and 785 models ONLY
DANGER
!
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and must be
installed for the protection of children and other at-risk
individuals.
The 784ECF Edgemont Craftsman Front Kit is intended to be used on Valor
heater model 780 & 785 with a required choice of Backing Plate 799BPB-1,
799BPB-2 or 799BPB-3.
Mounting of the 784 affects cavity dimensions—see below and installation
manual supplied with the heater for more information.
4007858-02
©2020, Miles Industries Ltd.
G4
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
½
¾
INSTALLER: Leave this
manual with the appliance.
CONSUMER: Retain this
manual for future reference.
Note: This kit must be
installed or serviced by a
qualified installer, service
agency or gas supplier. These
instructions are to be used
in conjunction with the main
installation instructions
for the above listed heater
model.
Cavity Depth
¾
with fan
¾
Overview (G4 and 799BPB sold separately)
G4 engine
799BPB
Backing Plate
784EC front
including doors
Publicité
Manuels Connexes pour Valor G4
Sommaire des Matières pour Valor G4
- Page 1 The 784ECF Edgemont Craftsman Front Kit is intended to be used on Valor heater model 780 & 785 with a required choice of Backing Plate 799BPB-1, 799BPB-2 or 799BPB-3.
- Page 2 Installation 3. Insert the top pin of the left door panel in the hole at the top of the left shroud already installed on the 1. Secure the backing plate (799BPB-1, 799PBP-2 or appliance. 799BPB-3 sold separately) to the appliance’s outer 4.
-
Page 3: Repair Parts List
Maintenance WARNING To clean the backing plate, use mild soap and water. You can dust the screen with a soft brush. To brush the back DO NOT TOUCH the barrier screen, of the screen, simply unhook it. front or glass while they are hot! Let the If the barrier becomes damaged, the barrier shall fireplace cool first before cleaning it. - Page 4 La Devanture Edgemont Craftsman 784EC est conçue pour les foyers Valor Legend G4 modèles 780 et 785. Elle doit être installée sur une des Plaques de finition 799BPB-1, 799BPB-2 ou 799BPB-3. L’installation de la Devanture 784 affecte les dimensions de la cavité—voir les détails ci-dessous de même que le guide d’installation fournis avec le foyer.
- Page 5 Installation 3. Insérez la cheville du haut dans le trou du support de devanture déjà installé sur l’appareil. 1. Fixez la plaque de finition (799BPB-1, 799BPB-2 ou 4. Soulevez le panneau et insérez la cheville du bas 799BPB-3 vendues séparément) aux supports des dans le trou du support.
-
Page 6: Entretien
Entretien AVERTISSEMENT Pour nettoyer la plaque de finition, utilisez une solution d’eau et de savon doux. Époussettez le pare-étincelles NE TOUCHEZ PAS le pare-étincelles ou le à l’aide d’une brosse à poils doux. Pour brossez l’arrière foyer lorsqu’ils sont chauds! Laissez-les du pare-étincelles, simplement décrochez-le.