Dremel DIGITAL High 398 Mode D'emploi page 7

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

!
Always unplug Rotary Tool before
WARNING
changing accessories, changing
collets or servicing your Rotary Tool.
SHAFT LOCK
BUTTON
COLLET
WRENCH
TO TIGHTEN
TO LOOSEN
COLLET
To loosen, first press shaft lock button and rotate the
shaft by hand until the lock engages the shaft
preventing further rotation.
!
Do not engage lock while the
C C A A U U T T I I O O N N
Rotary Tool is running.
With the shaft lock engaged use the collet wrench to
loosen the collet nut if necessary. Change accessories
by inserting the new one into the collet as far as
possible to minimize runout and unbalance. With the
shaft lock engaged, finger tighten the collet nut until the
accessory shank is gripped by the collet. Avoid
excessive tightening of the collet nut.
COLLETS
Four different size collets (see illustration), to
accommodate different shank sizes, are available for
your Rotary Tool. To install a different collet, remove the
collet nut and remove the old collet. Insert the unslotted
end of the collet in the hole in the end of the tool shaft.
Replace collet nut on the shaft. Always use the collet
which matches the shank size of the accessory you
plan to use. Never force a larger diameter shank into a
collet.
BALANCING ACCESSORIES
For precision work, it is important that all accessories
be in good balance (much the same as the tires on your
automobile). To true up or balance an accessory, slightly
loosen collet nut and give the accessory or collet a 1/4
turn. Retighten collet nut and run the Rotary Tool. You
should be able to tell by the sound and feel if your
accessory is running in balance. Continue adjusting in
Assembly
COLLET IDENTIFICATION CHART — Collet sizes can
be identified by the rings on the back end of collet.
1/32" Collet has one (1) ring.
1/16" Collet has two (2) rings.
3/32" Collet has three (3) rings.
1/8" Collet has no rings.
COLLET
COLLET
NUT
NUT
COLLET
480
1/8"
COLLET 481
this fashion until best balance is achieved. To maintain
balance on abrasive wheel points, before each use, with
the wheel point secured in the collet, turn on the Rotary
Tool and run the 415 Dressing Stone lightly against the
revolving wheel point. This removes high spots and
trues up the wheel point for good balance.
The hanger is provided for the use of hanging your
tool while using the flex-shaft or for storage. If you do
not use the hanger, remove it from the tool and snap
it back into place underneath the cord so it will be out
of the way while the tool is in use.
Flex-shaft to Rotary Tool installation
!
W W A A R R N N I I N N G G
kickback.
To attach the 225 flex-shaft (sold separately) to the
Rotary Tool press the shaft lock and remove the collet
nut, then remove the collet and housing cap as shown
in Figure 1. Install the driver cap on the motor shaft as
shown in Figure 2 and tighten.
!
C C A A U U T T I I O O N N
the driver cap finger tight and then tighten an additional
1/3 turn with the wrench. (Wrench included with your
Rotary Tool kit).
Page 7
3/32"
482
COLLET
1/16"
COLLET
Not for use with router bits. Use
with router bits will cause
To prevent damage to tool, do not
overtighten driver cap. Tighten
IDENTIFICATION
RINGS
483
1/32"
COLLET

Publicité

Table des Matières
loading

Produits Connexes pour Dremel DIGITAL High 398

Table des Matières