1. Manuels
  2. Marques
  3. Kalon Manuels
  4. Meubles pour bébés et tout-petits
  5. Caravan Crib 041
  6. Instruction pour le montage

Kalon Caravan Crib 041 Instruction Pour Le Montage

Masquer les pouces Voir aussi pour Caravan Crib 041:
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
ASSEMBLY
INSTRUCTIONS
CARAVAN
CRIB
INSTRUCTIONS
POUR LE
MONTAGE DU LIT
BEBE CARAVAN
o
Model N
: Caravan Crib 041 | KALON STUDIOS
www.kalonstudios.com | studio@kalonstudios.com
P.O. Box 292612 | Los Angeles | CA 90029 | 866.514.2034

Publicité

Table des Matières
loading

Manuels Connexes pour Kalon Caravan Crib 041

Sommaire des Matières pour Kalon Caravan Crib 041

  • Page 1 ASSEMBLY INSTRUCTIONS CARAVAN CRIB INSTRUCTIONS POUR LE MONTAGE DU LIT BEBE CARAVAN Model N : Caravan Crib 041 | KALON STUDIOS www.kalonstudios.com | studio@kalonstudios.com P.O. Box 292612 | Los Angeles | CA 90029 | 866.514.2034...
  • Page 3 ENTIRELY ORIGINAL DESIGN FOR A SUSTAINABLE CULTURE Made with uncompromising craftsmanship by traditional woodworkers in the USA from 100% sustainably-harvested, solid, domestic wood, the Caravan Collection is a celebration of craft and contemporary American woodworking. The unique character of the natural material is an integral part of the design that will only improve with age and use.

  • Page 4: Maintenance, Cleaning And Storage

    MAINTENANCE, CLEANING AND STORAGE Please take care to periodically check the crib/toddler bed to ensure that it is properly assembled and that no parts have come loose. Verify that the crib toddler bed parts remain fit snuggly against one another and tighten hardware if needed. Clean with a rag dampened with warm water.

  • Page 5: Table Des Matières

    PIECES INCLUDED / PIECES INCLUSES Refer to pouch for true to life diagram of hardware. Mattress Support ( x1 ) Support de matelas ( x1) Side Panel ( x2 ) Panneau latéral ( x2 ) Conversion Side Rail ( x1 ) Panneau de Conversion ( x1) Side Panel Foot ( x2 ) Panneau inférieur latéral ( x2 )

  • Page 6: A1 (X10)

    DETAIL / DÉTAIL 1 DETAIL / DÉTAIL 2 DETAIL / DÉTAIL 3...
  • Page 7 STEP 1 • Insert parts G into available holes at end of panel feet. • Fully thread parts B into holes along bottom edge of the Side and End Panels. (Detail 1) • Troubleshooting: Sometimes screw inserts can be blocked by small amounts of glue. If you encounter any obstruction when inserting hardware, thread the bolt in and out several times to clear the blockage.

  • Page 9: G (X4)

    STEP 2 • Insert parts E through holes on outer side of End Panels and End Panel Feet, then into holes on edge of Side Panels and Side Panel Feet. • Use the large Allen Key to loosly tighten parts E. Do not fully tighten hardware until all panels are attached and all parts E have been inserted.

  • Page 11: Mattress Support ( X1 )

    STEP 4 adjusting mattress height- lower setting • WARNING: If attached, Mattress Support End Rails must be removed from crib and/or mattress support. • Insert parts C through holes at bottom of mattress support and into holes on Side Panels. •...
  • Page 12 Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken. Contact Kalon Studios for replacement parts and instructional literature if needed. DO NOT substitute parts. • If refinishing, use a non-toxic finish specified for children’s products.
  • Page 13 CAUTION: Any mattress used in this crib shall be at least 69cm by 131cm with a thickness not exceeding 15cm.

Table des Matières