Setting The Timer - Global 246690 Manuel De L'utilisateur

Press or to adjust humidity between
26% and 90%.
Remember, if you select a humidity value BELOW 26% the
unit will display"CO" for continuous operation.
When desired humidity level is reached, press
NOTE:
1. When adjusting humidity between 26% and 90%,
operation halts until the humidity setting has been entered
and set. When set, the screen will display "completed",
and unit will automatically resume operation.
2. This unit has battery backed up memory to allow for
auto-restart. If power is interrupted, unit, will return to its
previous humidity setting and continue operation once
AC power is restored.

Setting the timer

Ensure clock is correct before setting the timer.
To set the timer, press
Timer on
Now press for
Timer off
To set a time for the unit to start, select "Timer on", set the
hour (00 to 23), and minute (00 to 59) fields to desired start
time. Once desired start time is reached, select "YES" to
set. To set the time for the unit to stop, select "Timer off"
and set the hour and minute fields to desired stop time.
Select "YES" to set.
To CANCEL the time display, move the cursor to
"ON" and press .
NOTE: Pressing the "Power ON/OFF" key during timer
operation will not cancel timer settings. Also, the unit will
not function if both the "Timer on" and "Timer off" settings
are the same.
Purging the unit
During normal operation the pump purges the condensate
reservoir automatically when full. However, use "PURGE"
before moving the machine to avoid water spillage. The
pump will shut off automatically after 40 seconds of
continuous operation.
Press the key to empty water from the
pump reservoir.
Make sure the drain hose is connected and routed to a
safe location.
Turning the unit OFF
DO NOT turn the power OFF by disconnecting the
power cord from the outlet!
Press the key once to turn the power OFF.
The LCD screen will display
the following message:
The water pump will turn on automatically and run for 40
seconds to drain the residual condensate water in the
dehumidifier.
To avoid water spillage DO NOT move the dehumidifier for
at least three minutes after turning the power OFF to allow
for drain time.
Before transporting, be sure to remove the external drain
hose, drain carefully, and return to the space provided on
the back of the unit.
LGR Dehumidifier Low-Grain Refrigerant
200 Pints Per Day Water Pump
to set.
then together.
Dehumidifier off
Draining....
ADDITIONAL LCD DISPLAY DATA
After Power OFF, the LCD may display summary screens
of recent activity and statistics. While not essential for unit
operation, this information may be useful for your records.
Standby CH00%
Ran 00000H
Standby CH00%
Last job 00:00
Standby CH00%
Time 00:00
MAINTENANCE
Replacing The Battery
1. Remove control panel label
and four corner screws in the
control panel.
2. Once removed, carefully lift the
control panel to access the PCB.
3. Remove battery and replace it
with CR2032 battery
4. Re-assemble control panel.
Cleaning or Replacing Filter
NOTE: The working performance of the dehumidifier will
be greatly reduced if filter is clogged. Check filter weekly.
Clean or replace filter if clogged or damaged.
Ensure the dehumidifier is turned
OFF and unplugged before
performing maintenance.
1. Remove filter as shown.
2. Vacuum any debris using vacuum
hose and nozzle attachment.
3. Using warm water and mild
detergent, wash filter and allow to dry.
4. Once dry, reinstall filter.
Water Pump Maintenance
NOTE: Water pump maintenance should be completed
once unit reaches 1000 hours of operation.
Turn dehumidifier OFF and unplug from outlet prior to
any maintenance.
1. Remove screws (6pcs) to separate front housing.
2. Remove water hoses to remove water pump.
3
User Manual
NOTE: The "RAN" field displays
continuously during operation.
Like a car odometer, this shows
the total number of hours on
the unit and cannot be manually
reset outside of the factory.