Sommaire des Matières pour Lechner Pure FullFit CU90
Page 1
All manuals and user guides at all-guides.com Pure FullFit customized (CU) Montage anleitung Installation Instructions Notice de montage...
Page 2
Ein Kochfeld nach Maß Das Induktionskochfeld CU ist in zwei Breiten erhältlich und jeweils in der Tiefe konfektionierbar (B x T): Pure FullFit CU90: 900 x 601 – 890 mm Pure FullFit CU120: 1200 x 601 – 890 mm Material-Kombinationen Das Induktionskochfeld Pure FullFit CU lässt sich mit folgenden Materialien...
Page 3
Le plan de cuisson à induction CU est disponible en deux largeurs et peut être fabriqué en deux profondeurs respectives (l x P) : Pure FullFit CU90 : 900 x de 601 à 890 mm Pure FullFit CU120 : 1200 x de 601 à 890 mm Combinaisons de matériaux...
All manuals and user guides at all-guides.com Montagezubehör Installation accessories Accessoires de montage 4x Doppelprofi l (Länge min. 1250mm) 2x Seitenprofi l (Länge min. 890mm) 2 Blatt Ausgleichsmasse mit je 6 Streifen 1x Edelstahl Aussteifungsprofi l bei 900 = Länge 868mm bei 1200 = Länge 1168mm 4 double profi les (length min.
Page 5
All manuals and user guides at all-guides.com 2 x 6...
All manuals and user guides at all-guides.com Unterschränke ausrichten Aligning base units Aligner les éléments bas Unterschränke ausrichten, sodass die Oberkanten aller Elemente das gleiche Niveau haben. Align base units so that the top edges of all elements are at the same level. Aligner les éléments bas si bien que les chants supérieurs de tous les éléments soient au même niveau.
Page 7
All manuals and user guides at all-guides.com...
Page 8
All manuals and user guides at all-guides.com Aussteifungsprofi l einschrauben Screwing on bracing profi le Visser le profi lé de renfort Aussteifungsprofi l bündig mit der Oberkante in das Element einschrauben. Screw bracing profi le onto the element so that it is fl...
Page 9
All manuals and user guides at all-guides.com...
Page 10
All manuals and user guides at all-guides.com Ausschnitte werkseits – Wrasenblech Factory-produced cut-outs – vapour strip Découpes réalisées en usine - tôle anti-buées 3 a-b) Vorgefräste Trägerplatten mit einem langen Stichsägeblatt von unten heraustrennen. 3 c-d) Ausschnitte mit einem Aluminiumklebeband vollfl ächig bekleben. 3 a-b) Using a long jigsaw blade, cut out the pre-milled support panels and remove them from below.
Page 11
All manuals and user guides at all-guides.com...
All manuals and user guides at all-guides.com Einpassen der Arbeitsplatten Fitting worktops Ajuster les plans de travail 4 a-b) Arbeitsplatten auf den ausgerichteten Unterschränken zusammen- legen. Höhendiff erenzen durch Unterlegen ausgleichen. 4 a-b) Position worktops on the aligned base units. Even out height diff...
Page 13
All manuals and user guides at all-guides.com...
Page 14
All manuals and user guides at all-guides.com Optional: Fixieren des Plattenstoßes Optional: Butt joint fi xing En option: fi xer le joint des panneaux Bei allen steinartigen Platten oder solchen, die in mehreren Teilstücken geliefert werden, fahren Sie mit Schritt 5 „Fixieren des Plattenstoßes”...
Page 15
All manuals and user guides at all-guides.com...
Page 16
All manuals and user guides at all-guides.com Fixieren des Plattenstoßes Butt joint fi xing Fixer le joint des panneaux 5 a-b) Plattenstöße reinigen. DE Spiritus 5 c-d) Plattenstöße mit Natur- EN Spirit stein-Silikon abdichten. FR Alcool 5 e) Arbeitsplatten zusammenfügen. 5 f) Arbeitsplatten ausrichten und positionieren.
Page 17
All manuals and user guides at all-guides.com DE Je nach Ausführung liegen 3 oder 4 Teilstücke bei. CU90: Breite = 900 mm CU120: Breite = 1200 mm EN Depending on configuration, there will be 3 or 4 sections. CU90: width = 900 mm, CU120: width = 1200 mm FR En fonction du modèle, 3 ou 4 segments de panneaux sont joints. CU90: largeur = 900 mm, CU120: largeur = 1200 mm PURE FULLFIT CU90 PURE FULLFIT CU120...
All manuals and user guides at all-guides.com Doppelprofi le aufbringen Fitting double profi les Poser les profi lés doubles 6 a) Doppelprofi l auf passende Länge kürzen und an den Enden im 45° Winkel auf Gehrung schneiden. 6 b) 2x Doppelprofi l bündig mit hinterer und vorderer Kante der Platte anbringen.
Page 19
All manuals and user guides at all-guides.com...
All manuals and user guides at all-guides.com Seitenprofi le aufbringen Fitting side profi les Poser les profi lés latéraux 7 a) Seitenprofi l auf passende Länge kürzen und an den Enden im 45° Winkel auf Gehrung schneiden. 7 b) 2x Seitenprofi l an linker und rechter Kante des Ausschnitts anbringen.
Page 21
All manuals and user guides at all-guides.com...
Page 22
All manuals and user guides at all-guides.com INDUKTIONSKOCHFELD PURE FULLFIT CUSTOMIZED...
Page 23
All manuals and user guides at all-guides.com Doppelprofi le aufbringen Fitting double profi les Poser les profi lés doubles 8 a) 1x Doppelprofi l auf passende Länge kürzen und an hinterer Kante des Ausschnitts anbringen. 8 b) Darauf achten, dass das Profi l 1cm Abstand zur Ausschnittkante aufweist.
Page 24
All manuals and user guides at all-guides.com...
Page 25
All manuals and user guides at all-guides.com Doppelprofi le aufbringen Fitting double profi les Poser les profi lés doubles 9 a) 2x Doppelprofi l auf passende Länge kürzen und an linker und rechter Kante des Ausschnitts anbringen. 9 b-c) Darauf achten, dass die Profi le 1cm Abstand zur Ausschnittkante aufweisen.
All manuals and user guides at all-guides.com Ausgleichsmasse aufbringen Applying levelling compound Appliquer la masse de compensation 10 a-b) Ausgleichsmasse nach Bedarf aufbringen. Auch hier ca. 1cm Abstand zum Ausschnitt einhalten. 10 a-b) Apply levelling compound if necessary. Allow a space of approx. 1 cm from the cut-out here as well.
Page 27
All manuals and user guides at all-guides.com 4-8x...
All manuals and user guides at all-guides.com Kochfeld einsetzen und ausrichten Fitting and aligning hob Insérer et aligner le plan de cuisson 11 a) Das Kochfeld mit Hilfe von Sauggriff en vorsichtig einsetzen. 11 b-c) Darauf achten, dass das Kochfeld umlaufend einen gleichmäßigen Abstand von ca .
Page 29
All manuals and user guides at all-guides.com...
All manuals and user guides at all-guides.com Stoßfuge reinigen Cleaning butt joints Nettoyer le joint 12) Reinigen Sie die Stoßfugen DE Spiritus mit Spiritus. EN Spirit FR Alcool 12) Clean the butt joints with spirit. 12) Nettoyer les joints avec de l‘alcool.
Page 31
All manuals and user guides at all-guides.com Kochfeld abdichten Sealing hob Étancher le plan de cuisson 13 a) Die Fugen mit Klebeband abkleben. 13 b) Fugen mit hitzebestän- digem Silikon abdichten. 13 c) Abziehen und Klebeband entfernen. 13 a) Mask the joints with adhesive tape.
Page 32
All manuals and user guides at all-guides.com Lechner Hungary Kft. Lechner Svenska Holding AB D. Lechner GmbH Erlbacher Straße 112 Madách Imre u. 26-28. Hinnerydsvägen 43 B 91541 Rothenburg o. d. Tauber 2534 Tát (Ipartelep) 287 34 Strömsnäsbruk DEUTSCHLAND MAGYARORSZÁG...