Lavorwash Apollo Mode D'emploi page 8

•
The machine should never be immersed and
never use the water jet against the appliance to
clean it.
• When using the machine in wet rooms (e.g. in
the bathroom) only connect it to sockets which
are connected in series with a ground fault
circuit interrupter. In case of doubt, consult an
electrician.
• Periodically examine the power cord and
machine for damage. If any damage is found,
do not use the appliance but contact your
service centre for repair.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similary qualified persons in order to
avoid a hazard.
• Should extension cables be used, ensure that
these lay on dry surfaces and protected against
water jets.
•
Before vacuuming liquids, check the float functions
correctly. When vacuuming liquids, and when the
tank is full, a float closes the suction opening, and
the vacuum operation is interrupted. Then switch
off the machine, disconnect the plug and empty
the tank. Regularly clean the water level limiting
device (float) and examine it for signs of damage.
•
If the machine overturns, it would be
recommended to release the trigger gun and
then stud up the machine.
•
If foam or liquid escape from the appliance, switch
off immediately.
•
The equipment should not be used to pick up
water from containers lavatories, tubs, etc.
• Aggressive solvents or detergents should not be
used.
• Service and repairs must be carried out by
qualified personnel only. Only use manufacturer
original spare parts for service repair.
• The manufacturer cannot be held responsible for
any damage/injury caused to persons, animals or
property caused by misuse of the appliance, not
in compliance with manual instructions.
Before removing the head (A) from the shaft
(I) remove the pipe (T1) and free the fasteners
(G).
Do not pull on the water hoses that lead
from the motor unit A to the tank T.
USAGE
DRY SUCTION (see fig. ③)
- Fit the filter (E) in the shaft (I).
8
- Fit the vacuum head (A) on the shaft (I) and
tighten with the fasteners (G).
- Fit the flexible hose (L) in the vacuum open-
ing (H).
- Fit the extensions (M) in the end of the flex
hose (L) and connect the most suitable ac-
cessory.
- Connect the appliance to a suitable socket.
- Start vacuuming by pressing switch (B).
WET SUCTION (see fig. ④)
- Fit the filter (C) under the head (A)
- Fit the vacuum head (A) on the shaft (I) and
tighten with the fasteners (G).
- Fit the flex pipe (L) in the vacuum opening
(H).
- Fit the extensions (M) in the end of the flex
hose (L) and connect the most suitable ac-
cessory.
- Connect the appliance to a suitable socket.
- Start vacuuming by pressing switch (B)
INJECTION-EXTRACTION WASHING SYSTEM
• Preparation:
- Fit filter (C) under the head (A)
- Pour the detergent product into the solu-
tion tank (T).
- Fit the vacuum head (A) on the shaft (I)
and tighten with fasteners (G).
- Fit the hydraulic pipe (T
(T)
- Fit the flex hose (L) into the vacuum open-
ing (H).
- Fit the end of the hydraulic pipe (U) on the
quick coupling on head (A) .
- Fit accessory (P) in the end of flex hose (L),
or fit the extensions (M) with accessories
(O and O )
1
- Fasten pipes (U
1
vided.
• Operation:
- Connect the appliance to a suitable socket.
- Press the lever on the tap and both the
switches (F) (B).
- To go ahead and wash, place the accessory
on the surface and, pressing the lever of
tap (D), pull it towards you.
- After completing the operation, turn off
) in solution tank
1
and U ) with the clips pro-
2