Ingersoll Rand 290 Notice page 20

1 Motor Housing Assembly . . . . . . 1712P–A40
2 Trigger . . . . . . . . . . . . . . . . . . 2934P–93
3 Trigger Spring . . . . . . . . . . . . 2934P–51
4 Trigger Pin . . . . . . . . . . . . . . . R1AF–524
5 Trigger Bushing . . . . . . . . . . . 2905–91S
S 6
Air Port Gasket (2) . . . . . . . . . R44H–210A
S 7
Gasket Retainer (2) . . . . . . . . . 2940–200
8 Throttle Valve Assembly . . . . 2934P–A50
S 9
Throttle Valve Face . . . . . . 2934–159
S 10
Throttle Valve Plunger . . . . . . 2934P–302
11 Throttle Valve Spring . . . . . 834–51
S 12
Air Strainer Screen . . . . . . . . . . . 434–61
13 Straight Inlet . . . . . . . . . . . . . . 845–565
S 14
Reverse Valve Bushing . . . . . . 2934P–330S
15 Reverse Valve Assembly . . . . . . 2934P–A329
16 Reverse Valve Seal . . . . . . . . . 85H–167
17 Reverse Lever . . . . . . . . . . . . . . . 2934–658A
18 Reverse Lock Plunger . . . . . . . . . 4U–663B
S 19
Reverse Lock Spring . . . . . . . . . . 4U–664
Power Regulator Assembly . . . . 2934P–A249
S 20
Power Regulator . . . . . . . . . . . 2934P–249
S 21
Power Regulator Seal . . . . . . . R1A–159
22 Power Regulator Retaining Ball . AV1–255
23 Housing Cover Lock Washer (4)
S 24
Housing Cover Cap Screw (4) . . 510–638
S 25
Housing Cover Assembly . . . . . . 1712P–A102
26 Oiler Adjusting Screw . . . . . . R2–71
27 Oiler Felt . . . . . . . . . . . . . . . . . R2–75
28 Grease Fitting . . . . . . . . . . . . . 130SR–188
S 29
Oil Chamber Plug . . . . . . . . . . R4–227
S 30
Oil Chamber Plug Gasket . . . . R4–92
31 Housing Cover Gasket . . . . . . . . 2934–283
32 Motor Clamp Washer . . . . . . . . . 2934–207
S 33
Cylinder . . . . . . . . . . . . . . . . . . . 2934–3
S 34
Cylinder Dowel . . . . . . . . . . . . . . 2934–98
35 Rear Rotor Bearing . . . . . . . . . . . 508–97
36 Rear End Plate . . . . . . . . . . . . . . 2934–12
37 Rotor . . . . . . . . . . . . . . . . . . . . . . 2934–53
S 38
Vane Packet (set of 6 Vanes) . . . . 2934–42–6
39 Front End Plate . . . . . . . . . . . . . . 2934–11
40 Front Rotor Bearing . . . . . . . . . . 810–97
S 41
Hammer Case Gasket . . . . . . . . . 2934–36
41A Dead Handle . . . . . . . . . . . . . . . . 834–48
42 Side Spade Handle . . . . . . . . . . . T15–41
43 Side Spade Handle Stud . . . . . . . 534–448
44 Side Spade Handle Nut . . . . . . . . 107–73A
44A Side Spade Handle Bracket . . . . . 2934–364
* Not illustrated.
S To keep downtime to a minimum it is desirable to have on hand certain repair parts. We recommend that you stock
one (pair or set) of each part indicated by a bullet (S ) for every four tools in service.
REFERENCE POUR COMMANDE DE LA PIECE
NUMERO DEL PEZZO PER L'ORDINAZIONE
SIMBOLO DE LA PIEZA PARA PEDIDOS
44B
45
46
47
48
49
50
50A
51
52
53
53A
8U–58 54
55
56
57
58
59
60
61
62
63
64
*
20
PART NUMBER FOR ORDERING
BESTELLNUMMER
BESTELNUMMERS
Hanger Spacer (2) . . . . . . . . . . . 2934–140
Hammer Frame Assembly . . . . 2934–A703
Hammer Pin (2) . . . . . . . . . . 2934–704
Hammer . . . . . . . . . . . . . . . . . . 1712–724
1" Square Drive Anvil
standard length . . . . . . . 1712–726
6" extended length . . . . 280–726–6
Hammer Case Assembly
for 290, 290–6 and
290–S . . . . . . . . . . . . . . 1712B–A727
for 290–EU and
290–6–EU . . . . . . . . . . 1712B–EU–A727
Hammer Case Bushing . . . . . 2934–641
Hammer Case Label
for 290, 290–6 and
290–S . . . . . . . . . . . . . . WARNING–2–99
for 290–EU and
290–6–EU . . . . . . . . . . EU–99
Hammer Case Cap Screw Lock
Washer (4) . . . . . . . . . . . . . . . . . 34U–58
Hammer Case Cap Screw (4) . . 834–638
Socket Retainer . . . . . . . . . . . . . RR10015S
Muffler . . . . . . . . . . . . . . . . . . . 2910–674
Spline Drive Anvil
standard length . . . . . . . 1712–A526
6" extended length . . . . 280–A514–6
Socket Retaining Ball . . . . . . D04–280
Retaining Ball Plunger . . . . . 845–230
Retaining Plunger Spring . . . 2940–231
Plunger Retaining Pin . . . . . . 845–128
Horizontal Hanger . . . . . . . . . . 2934–366
Nameplate
for 290–6 . . . . . . . . . . . 290–301–6
for 290–6–EU . . . . . . . 290–6–EU–301
for 290 and 290–S . . . . 290–301
for 290–EU . . . . . . . . . 290–EU–301
Nameplate Screw (3) . . . . . . . . C32–302
Bottle of Oil . . . . . . . . . . . . . . . 405–M01
Grease . . . . . . . . . . . . . . . . . . . . 405–MG1
Lube Injector . . . . . . . . . . . . . . . 230–228
Tune–up Kit (includes illustrated
parts 3, 4,6 [2], 7 [2], 9, 11,
12, 27,16, 21, 22,18, 19, 30, 31,
35, 38, 40 and 41) 290–TK2